[AT] MF 35 D lift

[John Maddock]

Many thanks Spencer.


JV



------ Original Message ------
From: "Spencer Yost" <spencer at rdfarms.com>
To: "Antique Tractor Email Discussion Group" 
<at at lists.antique-tractor.com>
Sent: Friday, 17 Sep, 2021 At 12:58 AM
Subject: Re: [AT] MF 35 D lift
After examining the emails, I see that they were not identical 
re-attempts of a single message, but are three different emails that 
contain different scans. So I let all of them through. They’re going to 
be 3-7MB folks. Be ready with the delete key if space is a problem on 
your device.

Spencer

Sent from my iPhone

On Sep 16, 2021, at 10:52 AM, Spencer Yost <spencer at rdfarms.com> wrote:

I’ll let one of the big, 6MB thru emails through  and delete the 
others.  

Spencer

Sent from my iPhone

On Sep 16, 2021, at 4:40 AM, John Maddock <agtronixjv at bigpond.com> 
wrote:

    
Wow!  Was I correct about the size limit!  I've received 3 response 
emails to say the mod. will review my emails coz they are *way* over the 
size limit.  If necessary, I can resend with one scan in each email, but 
hopefully Spencer will let the big ones through.


JV



------ Original Message ------
From: "Dennis Johnson" <moscowengnr at outlook.com>
To: "Antique Tractor Email Discussion Group" 
<at at lists.antique-tractor.com>
Sent: Thursday, 16 Sep, 2021 At 11:34 AM
Subject: Re: [AT] MF 35 D lift
  Tom,


After looking more, I think some of the linkage is messed up. I did find 
I had the eccentric roller, but it is not inline with the lever it is 
supposed to be touching. Wonder if it has sheared a pivot pin somewhere. 
That 1 lever does not appear to be in  a parallel plane to the others.

Need to disassemble more to try and figure things out.

Thanks for noting video- at least this gives me a hint of where problem 
is



Thanks

Dennis



Sent from my iPhone

  On Sep 15, 2021, at 7:21 PM, Tom Martin <tmartin at xtra.co.nz> wrote:




Actually they did toward the end of the video, most importantly the 
positioning of the levers
when replacing the top.

More tops would have been fulled off again because of incorrect 
placement of the levers,

than not.
Tom


   On 16 September 2021 at 11:17 Dennis Johnson 
<moscowengnr at outlook.com> wrote:

  Tom,


Yes I have seen that. They do not go into much detail on the levers in 
the top cover.



Thanks

Dennis


Sent from my iPad

  On Sep 15, 2021, at 6:07 PM, Tom Martin <tmartin at xtra.co.nz> wrote:




Hi Dennis

Have you watched this video?

https://www.youtube.com/watch?v=AmUc1AKWi9w 
<https://www.youtube.com/watch?v=AmUc1AKWi9w>


Tom
   On 10 September 2021 at 14:19 Dennis Johnson 
<moscowengnr at outlook.com> wrote:


I am confused about how the hydraulic lift linkage is supposed to work 
on my MF35D tractor. The lift lever does not move to the “up” position. 
I have not yet found how the linkage is supposed to work - drawing or 
video. I have seen some similar  u-tube videos on TO30/TO20, and MF 
multi-power, but not on the 35D.
FYI - installed new pump recently.

See attached picture of the linkage



Thanks

Dennis







    _______________________________________________
  AT mailing list
  AT at lists.antique-tractor.com
  http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com



    _______________________________________________
  AT mailing list
  AT at lists.antique-tractor.com
  http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com

    _______________________________________________
  AT mailing list
  AT at lists.antique-tractor.com
  http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com


    _______________________________________________
AT mailing list
AT at lists.antique-tractor.com
http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com 
<http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com>
_______________________________________________
AT mailing list
AT at lists.antique-tractor.com
http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com


_______________________________________________
AT mailing list
AT at lists.antique-tractor.com
http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com 
<http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.antique-tractor.com/pipermail/at-antique-tractor.com/attachments/20210917/5e762518/attachment.htm>