[AT] MF 35 D lift

[Spencer Yost]

I’ll let one of the big, 6MB thru emails through  and delete the others.  

Spencer

Sent from my iPhone

> On Sep 16, 2021, at 4:40 AM, John Maddock <agtronixjv at bigpond.com> wrote:
> 
> 
> Wow!  Was I correct about the size limit!  I've received 3 response emails to say the mod. will review my emails coz they are *way* over the size limit.  If necessary, I can resend with one scan in each email, but hopefully Spencer will let the big ones through.
> 
> JV
> 
> 
> 
> 
> ------ Original Message ------
> From: "Dennis Johnson" <moscowengnr at outlook.com>
> To: "Antique Tractor Email Discussion Group" <at at lists.antique-tractor.com>
> Sent: Thursday, 16 Sep, 2021 At 11:34 AM
> Subject: Re: [AT] MF 35 D lift
> 
>  Tom, 
> 
>  
>  
> After looking more, I think some of the linkage is messed up. I did find I had the eccentric roller, but it is not inline with the lever it is supposed to be touching. Wonder if it has sheared a pivot pin somewhere. That 1 lever does not appear to be in  a parallel plane to the others.
>  
> Need to disassemble more to try and figure things out.
>  
> Thanks for noting video- at least this gives me a hint of where problem is
>  
> 
>  
>  
> Thanks
>  
> Dennis
>  
> 
>  
>  
> Sent from my iPhone
>  
> 
>  
> On Sep 15, 2021, at 7:21 PM, Tom Martin <tmartin at xtra.co.nz> wrote:
>  
>  
>  
>  
>  
>  
> Actually they did toward the end of the video, most importantly the positioning of the levers
> 
>  
> when replacing the top.
>  
> 
>  
> More tops would have been fulled off again because of incorrect placement of the levers,
>  
> 
>  
> than not.
> 
>  
> Tom
>  
> 
>  
> 
>  
> 
>  
> 
>  
> 
>  
> On 16 September 2021 at 11:17 Dennis Johnson <moscowengnr at outlook.com> wrote: 
>  
>  Tom, 
> 
>  
>  
> Yes I have seen that. They do not go into much detail on the levers in the top cover.
>  
> 
>  
>  
> Thanks
>  
> Dennis 
>  
>  
> Sent from my iPad
>  
> 
>  
> On Sep 15, 2021, at 6:07 PM, Tom Martin <tmartin at xtra.co.nz> wrote: 
>  
>  
>  
>  
>  
>  
> Hi Dennis
>  
> 
>  
> Have you watched this video?
>  
> 
>  
> https://www.youtube.com/watch?v=AmUc1AKWi9w
>  
> 
>  
> 
>  
> 
>  
> Tom
>  
> 
>  
> On 10 September 2021 at 14:19 Dennis Johnson <moscowengnr at outlook.com> wrote: 
>  
>  
> I am confused about how the hydraulic lift linkage is supposed to work on my MF35D tractor. The lift lever does not move to the “up” position. I have not yet found how the linkage is supposed to work - drawing or video. I have seen some similar  u-tube videos on TO30/TO20, and MF multi-power, but not on the 35D. 
> FYI - installed new pump recently. 
>  
> See attached picture of the linkage
>  
> 
>  
>  
> Thanks
>  
> Dennis
>  
> 
>  
> 
>  
>  
>  
>  
>  
>  
> 
>   
> 
>  _______________________________________________ 
>  AT mailing list 
>  AT at lists.antique-tractor.com 
>  http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com 
>  
>  
>  
>  
>  
> 
>   
> 
>  
> _______________________________________________ 
>  AT mailing list 
>  AT at lists.antique-tractor.com 
>  http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com 
>  
>  
> 
>   
> 
>  _______________________________________________
>  AT mailing list
>  AT at lists.antique-tractor.com
>  http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com
>  
>  
>  
>    
> _______________________________________________
> 
> AT mailing list
> 
> AT at lists.antique-tractor.com
> 
> http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com
> 
> _______________________________________________
> AT mailing list
> AT at lists.antique-tractor.com
> http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.antique-tractor.com/pipermail/at-antique-tractor.com/attachments/20210916/f5e66418/attachment.htm>