[AT] 12V DC motor.

Bill Brueck bill at apluscomputer.com
Thu Mar 11 19:01:45 PST 2021


Glad your livestock won't go hungry for want of an auger drive, LOL.  You probably know you can reverse that Ford starter by rotating the commutator end plate 90 degrees.  Might involve lengthening the brush leads to reach the new position.  

B²
Bill Brueck
   Pine Island, MN USA

-----Original Message-----
From: AT <at-bounces at lists.antique-tractor.com> On Behalf Of Cecil Bearden
Sent: Thursday, March 11, 2021 8:41 PM
To: at at lists.antique-tractor.com
Subject: Re: [AT] 12V DC motor.

Unfortunately I lost the piece that was broke off.  I found a new motor today, and will get the old one rebuilt.  I spent a couple of hours adapting an old ford starter motor to fit, then found it turned the wrong direction.  New motor was $254 with bracket and pulley.  A new motor on Ebay was $248, so I don't think it was too high.  Then I had to work on the outlet chute.  The metal is really think and due to the salt in the feed it is rusty..
Cecil


On 3/11/2021 8:24 AM, szabelski at wildblue.net wrote:
> Cecil,
>
> Do you have the broken pieces? This may sound a little Rube Goldberg, but you can try gluing the pieces together using super glue. If there is enough room you can glue on some plastic reinforcement to the outside surfaces or give it a coating of epoxy. It may last long enough to get you through your work while trying to get a replacement.
>
> Carl
>
>
> ----- Original Message -----
> From: Cecil Bearden <crbearden at copper.net>
> To: at at lists.antique-tractor.com
> Sent: Wed, 10 Mar 2021 22:11:56 -0500 (EST)
> Subject: Re: [AT] 12V DC motor.
>
> Carl:
> I have it drying with a fan in front of it.  The trouble is it has a 
> broken brush holder.  The insulated one.  It looks like a Delco.  I 
> once could order all the parts from a place in Indiana but they closed down...
> Cecil
>
>
> On 3/10/2021 9:07 PM, szabelski at wildblue.net wrote:
>
>> Cecil,
>>
>> I’m guessing that you opened up the motor in order to know that water got in. Sometimes you can simply dry out the unit by separating it into its two main parts and baking them in an oven for a short while at a low temperature to remove any moisture. Then put it back together and test it on a bench. Don’t let the parts get too hot or you may damage the insulation on the wire and there’s no coming back from that. All you really want to do is try to remove any moisture.
>>
>> Carl
>>
>>
>> ----- Original Message -----
>> From: Cecil Bearden <crbearden at copper.net>
>> To: at at lists.antique-tractor.com
>> Sent: Wed, 10 Mar 2021 21:19:24 -0500 (EST)
>> Subject: [AT] 12V DC motor.
>>
>> The motor on my feed bin that augers out the feed to my welfare cows 
>> quit today.  It was a totally enclosed motor but it got water in it.  
>> It is very similar to an old late 50s early 60s Ford starter.  The 
>> front end at the output is round like a motor as it is clamped in a 
>> bracket to run on the feeder.   I cannot find one online, and it will 
>> be a week to get one from Bar 6 in KS where it was built.   Do any of 
>> you guys have a part number for something like this.
>>
>> _______________________________________________
>> AT mailing list
>> AT at lists.antique-tractor.com
>> http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com
>>
>> _______________________________________________
>> AT mailing list
>> AT at lists.antique-tractor.com
>> http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com
> _______________________________________________
> AT mailing list
> AT at lists.antique-tractor.com
> http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com
>
> _______________________________________________
> AT mailing list
> AT at lists.antique-tractor.com
> http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com
_______________________________________________
AT mailing list
AT at lists.antique-tractor.com
http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com


More information about the AT mailing list