[AT] 12V DC motor.
Cecil Bearden
crbearden at copper.net
Thu Mar 11 18:41:15 PST 2021
Unfortunately I lost the piece that was broke off. I found a new motor
today, and will get the old one rebuilt. I spent a couple of hours
adapting an old ford starter motor to fit, then found it turned the
wrong direction. New motor was $254 with bracket and pulley. A new
motor on Ebay was $248, so I don't think it was too high. Then I had to
work on the outlet chute. The metal is really think and due to the salt
in the feed it is rusty..
Cecil
On 3/11/2021 8:24 AM, szabelski at wildblue.net wrote:
> Cecil,
>
> Do you have the broken pieces? This may sound a little Rube Goldberg, but you can try gluing the pieces together using super glue. If there is enough room you can glue on some plastic reinforcement to the outside surfaces or give it a coating of epoxy. It may last long enough to get you through your work while trying to get a replacement.
>
> Carl
>
>
> ----- Original Message -----
> From: Cecil Bearden <crbearden at copper.net>
> To: at at lists.antique-tractor.com
> Sent: Wed, 10 Mar 2021 22:11:56 -0500 (EST)
> Subject: Re: [AT] 12V DC motor.
>
> Carl:
> I have it drying with a fan in front of it. The trouble is it has a
> broken brush holder. The insulated one. It looks like a Delco. I once
> could order all the parts from a place in Indiana but they closed down...
> Cecil
>
>
> On 3/10/2021 9:07 PM, szabelski at wildblue.net wrote:
>
>> Cecil,
>>
>> I’m guessing that you opened up the motor in order to know that water got in. Sometimes you can simply dry out the unit by separating it into its two main parts and baking them in an oven for a short while at a low temperature to remove any moisture. Then put it back together and test it on a bench. Don’t let the parts get too hot or you may damage the insulation on the wire and there’s no coming back from that. All you really want to do is try to remove any moisture.
>>
>> Carl
>>
>>
>> ----- Original Message -----
>> From: Cecil Bearden <crbearden at copper.net>
>> To: at at lists.antique-tractor.com
>> Sent: Wed, 10 Mar 2021 21:19:24 -0500 (EST)
>> Subject: [AT] 12V DC motor.
>>
>> The motor on my feed bin that augers out the feed to my welfare cows
>> quit today. It was a totally enclosed motor but it got water in it. It
>> is very similar to an old late 50s early 60s Ford starter. The front
>> end at the output is round like a motor as it is clamped in a bracket to
>> run on the feeder. I cannot find one online, and it will be a week to
>> get one from Bar 6 in KS where it was built. Do any of you guys have a
>> part number for something like this.
>>
>> _______________________________________________
>> AT mailing list
>> AT at lists.antique-tractor.com
>> http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com
>>
>> _______________________________________________
>> AT mailing list
>> AT at lists.antique-tractor.com
>> http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com
> _______________________________________________
> AT mailing list
> AT at lists.antique-tractor.com
> http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com
>
> _______________________________________________
> AT mailing list
> AT at lists.antique-tractor.com
> http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com
More information about the AT
mailing list