[AT] 12V DC motor.

Mike M meulenms at gmx.com
Wed Mar 10 20:03:34 PST 2021


WD40



On 3/10/2021 10:25 PM, Bill Brueck wrote:
> Cecil, could you post pics of the brush holder arrangement.  I have cores from that vintage and if it's like the automotive/industrial starters I'll probably have a brush holder for you.  And I'm set up to expedite ship.  Yeah, most of the units I've seen like you describe are Ford as they had the shaft sticking out the end of the starter, thus easy to modify to drive something.  Often a winch on the front of someone's Jeep.  And if it's Ford and the insulation is shot on the holder, common failure, you have room to work to reinsulate it and use a small bolt if you don't have rivets handy.
>
>> Bill Brueck
>     Pine Island, MN USA
>
> -----Original Message-----
> From: AT <at-bounces at lists.antique-tractor.com> On Behalf Of Cecil Bearden
> Sent: Wednesday, March 10, 2021 9:12 PM
> To: at at lists.antique-tractor.com
> Subject: Re: [AT] 12V DC motor.
>
> Carl:
> I have it drying with a fan in front of it.  The trouble is it has a broken brush holder.  The insulated one.  It looks like a Delco.  I once could order all the parts from a place in Indiana but they closed down...
> Cecil
>
>
> On 3/10/2021 9:07 PM, szabelski at wildblue.net wrote:
>
>> Cecil,
>>
>> I’m guessing that you opened up the motor in order to know that water got in. Sometimes you can simply dry out the unit by separating it into its two main parts and baking them in an oven for a short while at a low temperature to remove any moisture. Then put it back together and test it on a bench. Don’t let the parts get too hot or you may damage the insulation on the wire and there’s no coming back from that. All you really want to do is try to remove any moisture.
>>
>> Carl
>>
>>
>> ----- Original Message -----
>> From: Cecil Bearden <crbearden at copper.net>
>> To: at at lists.antique-tractor.com
>> Sent: Wed, 10 Mar 2021 21:19:24 -0500 (EST)
>> Subject: [AT] 12V DC motor.
>>
>> The motor on my feed bin that augers out the feed to my welfare cows
>> quit today.  It was a totally enclosed motor but it got water in it.
>> It is very similar to an old late 50s early 60s Ford starter.  The
>> front end at the output is round like a motor as it is clamped in a
>> bracket to run on the feeder.   I cannot find one online, and it will
>> be a week to get one from Bar 6 in KS where it was built.   Do any of
>> you guys have a part number for something like this.
>>
>> _______________________________________________
>> AT mailing list
>> AT at lists.antique-tractor.com
>> http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com
>>
>> _______________________________________________
>> AT mailing list
>> AT at lists.antique-tractor.com
>> http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com
> _______________________________________________
> AT mailing list
> AT at lists.antique-tractor.com
> http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com
> _______________________________________________
> AT mailing list
> AT at lists.antique-tractor.com
> http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com


--
This email has been checked for viruses by Avast antivirus software.
https://www.avast.com/antivirus




More information about the AT mailing list