<HTML><BODY><p style="margin-top: 0px;" dir="ltr">Just for information. The Troy-Bilt Horse will easily accept the Harbor freight 6.6 hp $99 engine. It is a direct replacement.The only change is the 5/16" bolt that goes in the end of the crank needs to be exchanged for metric.<br> I have done two. One pull starting and more than enough power.</p>
<div id="mail-app-auto-default-signature">
<p dir="ltr">--<br> Sent from myMail for Android</p>
</div>Monday, 27 September 2021, 05:47PM -07:00 from Carl Szabelski <a href="mailto:c.s.szabelski@gmail.com">c.s.szabelski@gmail.com</a>:<br><br><blockquote id="mail-app-auto-quote" style="border-left:1px solid #FC2C38; margin:0px 0px 0px 10px; padding:0px 0px 0px 10px;" cite="16327900610000414494">
<div class="js-helper js-readmsg-msg">
<style type="text/css"></style>
<div >
<base target="_self" href="https://e-aj.my.com/" />
<div id="style_16327900610000414494_BODY"><div class="cl_808973">Mike,<div><br></div><div>Not sure if I have the one you need. I’m going to be parting out an older unit that no longer is worth fixing. I purchased a new carb a few years back for it before it went south. I’ll take a look tomorrow and let you know. I think I kept the original receipt, so I should be able to give you the part number as a double check.</div><div><br></div><div>Carl<br><br>On Monday, September 27, 2021, Mike M <<a href="mailto:meulenms@gmx.com" target="_blank" rel=" noopener noreferrer" >meulenms@gmx.com</a>> wrote:<br><blockquote class="gmail_quote_mr_css_attr" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">Hi all,<br>
I have a question about Troy Built tillers; I have a '70's-80's Troy<br>
Bilt Horse tiller, well before they became MTD. I was moving it in high<br>
gear, over some hard clay to a place I wanted to till. Well, it hit the<br>
ground and took off like a bucking bronco. I started to go after it but<br>
having had my share of injuries this year I just let it go . It bounced<br>
and jumped all over the place, until it hit a tree, and cracked the<br>
carburetor flange. The engine is a HH60 Tecumseh, and all I need to<br>
repair it is a new carb. The problem is I cannot find one with the<br>
plate, and tall screw that is riveted on to accept the vertical air<br>
cleaner. Any help would be appreciated.<br>
<br>
Thanks,<br>
Mike M<br>
<br>
<br>
--<br>
This email has been checked for viruses by Avast antivirus software.<br>
<a href="https://www.avast.com/antivirus" target="_blank" rel=" noopener noreferrer" >https://www.avast.com/antivirus</a><br>
<br>
_______________________________________________<br>
AT mailing list<br>
<a href="mailto:AT@lists.antique-tractor.com" target="_blank" rel=" noopener noreferrer" >AT@lists.antique-tractor.com</a><br>
<a href="http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com" target="_blank" rel=" noopener noreferrer" >http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com</a><br>
</blockquote></div>
</div></div>
<div>_______________________________________________<br>
AT mailing list<br>
<a href="mailto:AT@lists.antique-tractor.com">AT@lists.antique-tractor.com</a><br>
<a href="http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com" target="_blank" >http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com</a><br>
</div>
<base target="_self" href="https://e-aj.my.com/" />
</div>
</div>
</blockquote></BODY></HTML>