<div dir="ltr"><div class="gmail_default" style="font-family:tahoma,sans-serif">Is that the original coil?</div><div class="gmail_default" style="font-family:tahoma,sans-serif"><br></div><div class="gmail_default" style="font-family:tahoma,sans-serif">I'm not familiar with the 454, but in the truck world, most coils are intended for 6V use.  There is a resistor wire in the harness that drops the voltage while the current is flowing with the points closed.  But there are also coils intended for 12V use with no resistor wire.  If that is not the original coil, perhaps you have the wrong one.</div><div class="gmail_default" style="font-family:tahoma,sans-serif"><br></div><div class="gmail_default" style="font-family:tahoma,sans-serif">Since it seems to work fine with 12V applied, I'd probably run another wire from the ignition switch to the coil to bypass any possible resistor wire.</div><div class="gmail_default" style="font-family:tahoma,sans-serif"><br></div><div class="gmail_default" style="font-family:tahoma,sans-serif">Howard</div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Wed, Aug 25, 2021 at 11:08 PM John Hall <<a href="mailto:jtchall@nc.rr.com">jtchall@nc.rr.com</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><br>
If there is, I can't find it. Closes thing I have found is the <br>
diode/rectifier for the alternator. Its inline and is tied in on this <br>
particular "circuit" . Matter of fact, the side opposite the alternator <br>
is where the fuel solenoid feeds from.<br>
<br>
John Hall<br>
<br>
<br>
On 8/25/2021 11:05 PM, Spencer Yost wrote:<br>
> Maybe there’s an external resistor?<br>
><br>
> Spencer<br>
><br>
> Sent from my iPhone<br>
><br>
>> On Aug 25, 2021, at 10:35 PM, John Hall <<a href="mailto:jtchall@nc.rr.com" target="_blank">jtchall@nc.rr.com</a>> wrote:<br>
>><br>
>> Got what I hope is a simple question. On my IH 454 tractor, is the voltage going to the coil a constant 12V? I'm having some issues with it running bad when it gets hot (I've already replaced everything but the plug wires). Found out today that if I run a jumper wire from battery to the coil, the problem goes away. Take it off problem comes back, put it back it goes away, take it off, it comes back. So I am tracing the wiring but this one isn't simple, new enough there are tons of gauges, fuel solenoids, safety switches, etc. Anyway, if I check voltage at the coil, the fuel solenoid, and there is one small terminal on starter solenoid that all read 12V if the switch is on. If I bump the engine over slightly (I guess the pts are closing) then the coil and starter drop to just under 6V, fuel solenoid stays the same. So shouldn't there always be 12V at the coil?<br>
>><br>
>> John Hall<br>
>> _______________________________________________<br>
>> AT mailing list<br>
>> <a href="mailto:AT@lists.antique-tractor.com" target="_blank">AT@lists.antique-tractor.com</a><br>
>> <a href="http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com" rel="noreferrer" target="_blank">http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com</a><br>
>><br>
> _______________________________________________<br>
> AT mailing list<br>
> <a href="mailto:AT@lists.antique-tractor.com" target="_blank">AT@lists.antique-tractor.com</a><br>
> <a href="http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com" rel="noreferrer" target="_blank">http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com</a><br>
<br>
_______________________________________________<br>
AT mailing list<br>
<a href="mailto:AT@lists.antique-tractor.com" target="_blank">AT@lists.antique-tractor.com</a><br>
<a href="http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com" rel="noreferrer" target="_blank">http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com</a><br>
</blockquote></div><br clear="all"><div><br></div>-- <br><div dir="ltr" class="gmail_signature"><div dir="ltr">Howard</div></div>