<div dir="ltr">Agreed with Milo and Jim B.  Handy to have a set of picks, something like you see here (um, yeah, this is a shameless plug, I work for Central Tools)<div><br></div><div><a href="https://www.centraltools.com/hook-and-pick-sets/">https://www.centraltools.com/hook-and-pick-sets/</a><br></div><div><br></div><div>And I'll add, penetrating oil.  You want to take as much fight out of that clip as possible, or you'll just be messing up your pick set.</div><div><br></div><div>SO</div><div><br></div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Thu, May 13, 2021 at 1:11 PM Jim Becker <<a href="mailto:mr.jebecker@gmail.com">mr.jebecker@gmail.com</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">

<div dir="ltr">
<div dir="ltr">
<div style="font-size:12pt;font-family:Calibri;color:rgb(0,0,0)">
<div>Sometimes one end is cut at an angle.  You will have a little better 
luck with Milo’s method if you try getting the pick under the end with the angle 
cut.  If both ends are cut square, it will be difficult.</div>
<div> </div>
<div>Jim Becker</div>
<div style="font-size:small;text-decoration:none;font-family:Calibri;font-weight:normal;color:rgb(0,0,0);font-style:normal;display:inline">
<div style="font:10pt tahoma">
<div><font size="3" face="Calibri"></font> </div>
<div style="background:rgb(245,245,245)">
<div><b>From:</b> <a title="milo@milosmachineshed.com">Milo</a> </div>
<div><b>Sent:</b> Thursday, May 13, 2021 11:40 AM</div>
<div><b>To:</b> <a title="at@lists.antique-tractor.com">at@lists.antique-tractor.com</a> </div>
<div><b>Subject:</b> Re: [AT] Removing clips</div></div></div>
<div> </div></div>
<div style="font-size:small;text-decoration:none;font-family:Calibri;font-weight:normal;color:rgb(0,0,0);font-style:normal;display:inline">
<p>My best success comes from a small straight blade screwdriver to hold one 
end, while working a right angle (very sharp point) short pick under the other 
end.<br></p><pre cols="72">Peace
Milo
<a href="http://milosmachineshed.com" target="_blank">milosmachineshed.com</a></pre>
<div>On 5/13/2021 12:26 PM, Spencer Yost wrote:<br></div>
<blockquote type="cite"><pre>I replaced a bent pto shaft on an implement a few weeks ago.   I had to remove the two outer clips and press it out. I put it back together in a hurry and I decided to reuse the clips. Bad choice. During tedding a clip came off and the cross lost its cups and needle bearings.



So I am replacing with a new cross kit and most notably, I have a clip to remove now.  I just remember the first time it was a real bugger because these clips don’t have holes in them. I can’t remember how I eventually did it (I think I finally was able to anchor one side and get a cotter pin remover under the other side) but I used cuss words I haven’t used in a long time and spent way more time than I am willing to spend this time.

So I thought I’d ask for advice.

How do you folks remove these? (Pic below)  I’ve searched all over the Internet but everyone’s got those clips with the ears or clips with holes in them in all the videos I’ve seen. I’ve seen a few mentions on forums but they all do things like drill behind it so you can stick a nail in and push it and other stuff like that.

Thanks in advance!

</pre></blockquote></div></div></div></div>
_______________________________________________<br>
AT mailing list<br>
<a href="mailto:AT@lists.antique-tractor.com" target="_blank">AT@lists.antique-tractor.com</a><br>
<a href="http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com" rel="noreferrer" target="_blank">http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com</a><br>
</blockquote></div>