<div dir="ltr">GREAT question, Spencer.  There are some truly oddball taps and dies readily available, although HomeDepot does surprise me.  I use MSC for most  tooling, and the sheer number of choices in taps (and dies, I guess, although I purchase few dies) is mind-boggling.<div><br></div><div>Here's an example.  In metric, M8 is quite common - as common as 5/16-18 in the inch system.  The metric fastener system does have a concept of coarse and fine, but it skews heavily to the coarse.  M8 x 1.25 is about as common as metric dirt.  Now, check this out:  In just the spiral-flute style, MSC lists five sizes, including:  M8 x 0.5, M8 x 0.75, M8 x 1.0, M8 x 1.25, and M8 x 1.5.  And the number of choices!  I kid you not, there are 429 different choices in the M8 x 1.25 size alone, spiral flute alone.  We haven't even looked at straight flute nor spiral point styles.  Different materials (HSS, cobalt, vanadium, carbide) with or without a variety of different coatings, and with different classes of fit (for example, a series of oversize increments are readily available that make threads to be plated later).</div><div><br></div><div>SO</div><div><br></div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Sun, May 5, 2019 at 12:45 AM Spencer Yost <<a href="mailto:spencer@rdfarms.com">spencer@rdfarms.com</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div dir="auto">You are correct Steve - just had it reversed in my mind (or in my typing, just returned from a long trip and can’t even remember what I did this morning).<div><br></div><div>So I did spend some time searching ( should have done that first I guess).  You are right - unicorns for sure.   The only reference I could find were plugs and this one bolt, which might work:</div><div><br></div><div><a href="https://www.gmpartsdirect.com/oem-parts/gm-steering-wheel-bolt-m15x1-5x29-11610164" target="_blank">https://www.gmpartsdirect.com/oem-parts/gm-steering-wheel-bolt-m15x1-5x29-11610164</a></div><div><br></div><div>Wonder why the taps and dies are so easy to come by if the bolts are so rare.   Heck, Home Depot even has them:</div><div><br></div><div><a href="https://www.homedepot.com/p/Drill-America-m15-x-1-5-Carbon-Steel-Hex-Re-Threading-Die-DWTSMH15X1-5/305502698" target="_blank">https://www.homedepot.com/p/Drill-America-m15-x-1-5-Carbon-Steel-Hex-Re-Threading-Die-DWTSMH15X1-5/305502698</a></div><div><br></div><div>  And it frequently shows up on charts:</div><div><br></div><div><a href="https://www.newmantools.com/tech/threadmf.htm" target="_blank">https://www.newmantools.com/tech/threadmf.htm</a></div><div><br></div><div><br></div><div>Maybe it just fell out of favor?</div><div><br><br><div dir="ltr" id="gmail-m_-2902024396597168229AppleMailSignature">Spencer Yost</div><div dir="ltr"><br>On May 4, 2019, at 1:54 PM, Stephen Offiler <<a href="mailto:soffiler@gmail.com" target="_blank">soffiler@gmail.com</a>> wrote:<br><br></div><blockquote type="cite"><div dir="ltr"><div dir="ltr">Oh, and with apologies for the continued critique Spencer, M15 x 1.0 would be a very fine pitch, not coarse.   For comparison, M14 x 1.5 is the fine pitch and M14 x 2.0 is the coarse pitch.<div><br></div><div>SO</div><div><br></div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Sat, May 4, 2019 at 1:40 PM Stephen Offiler <<a href="mailto:soffiler@gmail.com" target="_blank">soffiler@gmail.com</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div dir="ltr">Spencer:  I still question the 15mm fastener.  I originally checked McMaster-Carr before I ever commented; now, I've double-checked there plus MSC and Grainger.  These are THE three "go-to" industrial suppliers online.  None carry 15mm fasteners.  They go straight from 14mm to 16mm.<div><br></div><div>SO</div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Sat, May 4, 2019 at 10:47 AM Spencer Yost <<a href="mailto:spencer@rdfarms.com" target="_blank">spencer@rdfarms.com</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">I’ve been giving this some more thought, and I am actually now a little more serious about metric if you can tolerate the idea of a metric bolt on a canon.. All you need are:<br>
<br>
15 mm x 1 threads per millimeter tap.<br>
14 mm drill for initial boring prior to tapping.<br>
A 15 mm x 1 threads per millimeter bolt at the length you need.<br>
<br>
No special tooling, no  excessive drilling diameters, etc.  A single thread per mm is a course pitch so it meets that requirement.  This is all fairly cheap, straightforward, available from major Internet retailers and probably your local fastener store if you have such a beast. I am lucky - I have three.<br>
<br>
<br>
Anyway you go, best of luck.<br>
<br>
Spencer Yost<br>
<br>
> On May 4, 2019, at 9:58 AM, James Peck <<a href="mailto:jamesgpeck@hotmail.com" target="_blank">jamesgpeck@hotmail.com</a>> wrote:<br>
> <br>
> About 10 years ago I was on a flight to Kansas. I can't quite remember the sequence of events. I heard large men speaking a language I do not remember hearing before as I got on the flight. One ended up seated next to me. Turned out they were from Dronningsborg and were going to Agco in Hesston for a project meeting. <br>
> <br>
> I asked what they were doing about metric fasteners. The Dane said that they had been all metric until Agco purchased them. They had been switched to mixed metric and SAE.<br>
> <br>
> It may be irrelevant. Agco shut down Dronningsborg and bought into Laverda. Are the combines made for Agco by Laverda all metric? Why would they not be?<br>
> <br>
> <a href="https://en.wikipedia.org/wiki/Randers" rel="noreferrer" target="_blank">https://en.wikipedia.org/wiki/Randers</a><br>
> <br>
> [Al Jones] Metric is the work of the devil...…..<br>
> <br>
> Helicoils are wonderful.  Very easy to do and they WORK!<br>
> <br>
> My white demonstrator Super A that I have been tinkering off and on forever had four badly stripped holes in the torque tube.  Somebody had tapped the 5/8" holes out about 7/8 or so and it was BAD.  There wasn't any threaded inserts that I could find that would be direct replacements.  A machine shop friend of mine was nice enough to make a set of inserts, kind of like the KeenSerts, and install in the torque tube.  Once it's painted I don't think you'll be able to tell that anything ever happened to it!<br>
> _______________________________________________<br>
> AT mailing list<br>
> <a href="mailto:AT@lists.antique-tractor.com" target="_blank">AT@lists.antique-tractor.com</a><br>
> <a href="http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com" rel="noreferrer" target="_blank">http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com</a><br>
<br>
_______________________________________________<br>
AT mailing list<br>
<a href="mailto:AT@lists.antique-tractor.com" target="_blank">AT@lists.antique-tractor.com</a><br>
<a href="http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com" rel="noreferrer" target="_blank">http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com</a><br>
</blockquote></div>
</blockquote></div>
</div></blockquote><blockquote type="cite"><div dir="ltr"><span>_______________________________________________</span><br><span>AT mailing list</span><br><span><a href="mailto:AT@lists.antique-tractor.com" target="_blank">AT@lists.antique-tractor.com</a></span><br><span><a href="http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com" target="_blank">http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com</a></span><br></div></blockquote></div></div>_______________________________________________<br>
AT mailing list<br>
<a href="mailto:AT@lists.antique-tractor.com" target="_blank">AT@lists.antique-tractor.com</a><br>
<a href="http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com" rel="noreferrer" target="_blank">http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com</a><br>
</blockquote></div>