[AT] MF 35 D lift

[John Maddock]

'Morning Dennis


I've scanned 9 pages which appear most relevant. I have a vague 
recollection that there is a size limit on emails so I'll send 3 scans 
with each of 3 emails.


Unfortunately, for reasons unknown, I don't have a number of diagrams. 
It may be that they are in the section on Pressure Control which I have 
not brought from the workshop, but hopefully the one related to Position 
Control will be adequate for your needs.


Hope this helps


JV



------ Original Message ------
From: "Dennis Johnson" <moscowengnr at outlook.com>
To: "Antique Tractor Email Discussion Group" 
<at at lists.antique-tractor.com>
Sent: Thursday, 16 Sep, 2021 At 11:34 AM
Subject: Re: [AT] MF 35 D lift
  Tom,


After looking more, I think some of the linkage is messed up. I did find 
I had the eccentric roller, but it is not inline with the lever it is 
supposed to be touching. Wonder if it has sheared a pivot pin somewhere. 
That 1 lever does not appear to be in  a parallel plane to the others.

Need to disassemble more to try and figure things out.

Thanks for noting video- at least this gives me a hint of where problem 
is



Thanks

Dennis



Sent from my iPhone

  On Sep 15, 2021, at 7:21 PM, Tom Martin <tmartin at xtra.co.nz> wrote:




Actually they did toward the end of the video, most importantly the 
positioning of the levers
when replacing the top.

More tops would have been fulled off again because of incorrect 
placement of the levers,

than not.
Tom


   On 16 September 2021 at 11:17 Dennis Johnson 
<moscowengnr at outlook.com> wrote:

  Tom,


Yes I have seen that. They do not go into much detail on the levers in 
the top cover.



Thanks

Dennis


Sent from my iPad

  On Sep 15, 2021, at 6:07 PM, Tom Martin <tmartin at xtra.co.nz> wrote:




Hi Dennis

Have you watched this video?

https://www.youtube.com/watch?v=AmUc1AKWi9w 
<https://www.youtube.com/watch?v=AmUc1AKWi9w>


Tom
   On 10 September 2021 at 14:19 Dennis Johnson 
<moscowengnr at outlook.com> wrote:


I am confused about how the hydraulic lift linkage is supposed to work 
on my MF35D tractor. The lift lever does not move to the “up” position. 
I have not yet found how the linkage is supposed to work - drawing or 
video. I have seen some similar  u-tube videos on TO30/TO20, and MF 
multi-power, but not on the 35D.
FYI - installed new pump recently.

See attached picture of the linkage



Thanks

Dennis







    _______________________________________________
  AT mailing list
  AT at lists.antique-tractor.com
  http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com



    _______________________________________________
  AT mailing list
  AT at lists.antique-tractor.com
  http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com

    _______________________________________________
  AT mailing list
  AT at lists.antique-tractor.com
  http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com


    _______________________________________________
AT mailing list
AT at lists.antique-tractor.com
http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com 
<http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.antique-tractor.com/pipermail/at-antique-tractor.com/attachments/20210916/771f02ed/attachment.htm>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: MF hyd. lift 1.pdf
Type: application/pdf
Size: 592243 bytes
Desc: not available
URL: <http://lists.antique-tractor.com/pipermail/at-antique-tractor.com/attachments/20210916/771f02ed/attachment-0004.pdf>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: MF hyd. lift 3.pdf
Type: application/pdf
Size: 1571724 bytes
Desc: not available
URL: <http://lists.antique-tractor.com/pipermail/at-antique-tractor.com/attachments/20210916/771f02ed/attachment-0005.pdf>