[AT] Hay baling fun...

Sun Jul 18 19:11:27 PDT 2021

Cecil,

Have you tried to break the bearing free using a flat nose chisel? Place
the chisel against the inner race and hit with a hammer once or twice.
Move the chisel to the opposite side of the shaft and hit it once or twice
again, you may be able to walk the bearing off of the shaft.

Carl

On Sunday, July 18, 2021, Cecil Bearden <crbearden at copper.net> wrote:

> Trying to get the salvage oscillator off the swather.  It is a spindle
> with a wheel on one end. Parts book calls it a flywheel. OK..  Uses wheel
> bearings and tightens just like a wheel bearing. Took everything off and
> the outer bearing is stuck on the shaft and will not drive out.  Ruined the
> nut on the end of the shaft trying to drive out with a 3lb hammer.  No way
> to use a puller.  I may try to get the welder close and use the carbon arc
> torch.  Put an arc carbon on each side of the inner race and heat to break
> it loose.
>
> Cecil
>
>
> On 7/18/2021 7:54 AM, Mark Johnson wrote:
>
>> Cecil:
>>
>> With rain coming in you will be baling what we used to call 'very clean
>> hay' soon.
>>
>> Stories like this make me realize that NOT going back to the farm when I
>> was 40 was the right move for me. Sorry to hear you're having so much
>> equipment trouble.
>>
>> Mark J
>>
>> On 7/18/2021 7:44 AM, Cecil Bearden wrote:
>>
>>> Long story.  My 648 New Holland round baler baled 47 bales and about
>>> Noon, the knife would not cut wrap.  Baled another 3 bales after installing
>>> new roll of wrap. Climbed up on top of baler each time to try to get knife
>>> to cut.  Called my buddy at Chickasha who is a baler expert.  He had not
>>> worked on that one. Called Local New Holland dealer and baler guy said he
>>> had not worked on that model and it was to old.  Only a 2000 model.    I
>>> opened up the side covers and looked at main drive chains and they were
>>> coming apart and cutting a slot in main frame!  and had cut grooves in the
>>> teeth of the Drive sprocket. It was fine when I started..
>>>
>>> Wife asked how much is a new one??  Just take it out of your 401k before
>>> the gov't gets it all.  I made a few calls and the local NH dealer did not
>>> have anything in a 4ft wide baler.   I have 12 rolls of Net for 4 ft wide.
>>> So the Vermeer dealer delivered a new Vermeer 504R Premium at 3:30pm.  I
>>> finished at 11:30 that night. I still like my old one better.  This one has
>>> a touch screen that drives me nuts in the cab at night.  It is so bright on
>>> the lowest setting it is like a house of mirrors in the cab.  No night
>>> setting.  It seems to run slower on the belts than the old NH, so it takes
>>> longer to wrap but bales may be a bit denser.  This one has  a hyd pickup
>>> that is a pain in the butt since I have to disconnect my loader to connect
>>> the pickup.  And with a loader on I have to drive with the loader at 7ft
>>> above the ground to see the windrow.  No fault of the baler.  I got 128
>>> bales baled..   The monitor tells me how many bales per hour, how many
>>> minutes per bale, and the moisture.  15 % on one field and wet on the
>>> other. Really tells me a lot!!   I really want my old one running
>>> again..    I bought my old one in 2005 for $10K  I baled for 12 years and
>>> spent about $3500 for bearings gears and belts.  It needs about $1500 in
>>> chains and sprockets now, and the knife problem is something on an
>>> adjustment.  The knife drops by gravity, and I have looked at it so many
>>> times trying to figure out what raises it when the chamber opens I finally
>>> gave up.  I have not found a dealer who can tell me yet.   The new one is
>>> not better by the $26500 difference in price.  I had 30 acres of hay down
>>> that resulted in 121 bales at $50/bale, so I had to do something.  Forecast
>>> was for rain that evening and it only sprinkled for 5 minutes. I had
>>> another baler in a shed that I bought but it needed some parts and I did
>>> not  know anything about it.
>>>
>>> I started laying hay down again yesterday and after 3 acres the swather
>>> pitman oscillator bearing went out and during removing the collar the shaft
>>> broke on the oscillator.  I have another on a salvage swather but the
>>> bearings seem to be frozen on the spindle.  Then we had a cold front come
>>> through and an inch of rain.  Heat and humidity and more rain today......
>>> Cecil
>>>
>>> _______________________________________________
>>> AT mailing list
>>> AT at lists.antique-tractor.com
>>> http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com
>>>
>> _______________________________________________
>> AT mailing list
>> AT at lists.antique-tractor.com
>> http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com
>>
> _______________________________________________
> AT mailing list
> AT at lists.antique-tractor.com
> http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.antique-tractor.com/pipermail/at-antique-tractor.com/attachments/20210718/72988869/attachment.htm>