[AT] Questionable ignition coil

[Spencer Yost]

Sorry to reply to my own message, but I forgot something. Also check voltage drop. Going into the coil from the ignition switch, you should see battery voltage. For instance if your battery is putting out 6.2 you should see roughly 6.2 going to the coil. On the other terminal end of the coil, there will be a slight voltage drop.  However on my bad coil with the Pacer voltage had dropped all the way to 3.7 from 6.3V.   Can not remember what a good voltage drop is.   Surprising large if I remember right, but not 50%.  Maybe I’ll run to the Pacer a little later and see.

I don’t know electricity or electronics well enough to know how or why that occurred with reasonable resistance readings but that measurement was the only out of range number I got.

I got that little tip from Brice Adams and what was the final straw causing me to get an exchange rather than just continuing to run on the old one.

Spencer

Sent from my iPhone

> On Nov 6, 2019, at 11:03 AM, Spencer Yost <spencer at rdfarms.com> wrote:
> 
> With an ohmmeter across the two screw terminals, test resistance.  Then test across negative and the coil wire socket.  Make sure you don’t have zero or an infinite reading on either. Any other reading is highly coil specific and hard to generalize.   I usually see 1-9ohms depending on which of the two tests, voltage, brand, age, etc.
> 
> However, having said this, I find the tests generally useless as most coils fail on load and heat and these tests do not rule out these issues.  For instance I once had a Farmall A coil that would die when hot but tested fine on the bench.  A new coil and the tractor purred all day long for another year or two till I sold it.
> 
> Another note:  about two years ago I gave the Pacer a tuneup.  Would hardly run.   I couldn’t figure it out until, out of frustration, I put the old coil back on.   Ran great.   The new coil tested fine.   Fortunately I had bought the coil from Napa and they exchanged it.  The second new one worked fine and I am still running on it.  So you can get a bad coil out of the box in these days of poor quality analog ignition components.
> 
> I’m sure others more knowledgable will jump in with additional advice.
> 
> Spencer
> 
> Sent from my iPhone
> 
>>> On Nov 5, 2019, at 8:19 PM, Gilbert Schwartz <vschwartz1 at comcast.net> wrote:
>>> 
>> 
>> I would like to try and delve into the wide knowledge and expertise of the members within ATIS. 
>> Is there any acceptable method of determining if an ignition coil is good short of installing it on a running engine. Our 1949 AC G would not start a few days ago after being parked for a short period of time. A quick observation determined the contact points were beyond use. I went to the local auto parts store and was advised I probably should replace both the points and of the condenser because they felt like that condenser went first and it caused the points to burn up. With this information I also purchased a new coil even though I wondered if the coil was a bad.
>> Bottom line; Is there any way to bench test a coil? We have several used coils laying around here of questionable viability. I would like to pitch them if they aren't any good. 
>> I appreciate anything you can tell me.
>> _______________________________________________
>> AT mailing list
>> AT at lists.antique-tractor.com
>> http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com
> _______________________________________________
> AT mailing list
> AT at lists.antique-tractor.com
> http://lists.antique-tractor.com/listinfo.cgi/at-antique-tractor.com
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.antique-tractor.com/pipermail/at-antique-tractor.com/attachments/20191106/bfeb3f7b/attachment.htm>