[AT] 430V update

[Brian VanDragt]

Davenport Tractor has screws and nuts that look like the Airloc fasteners but are threaded instead of 1/4 turn:

http://www.davenporttractor.com/c-12-hood-fasteners.aspx
http://www.davenporttractor.com/c-12-hood-fasteners.aspx

Brian


> On October 12, 2017 at 9:59 PM Spencer Yost wrote:
> 
> 
>     Yea. I sort of thought they were something like that, just not bonded to the discs.
> 
>     As a sidenote: does anyone know where to get the airlock fasteners for John Deere sheet metal? I need the "female" half of a fastener. I have one that's just trashed and the male part won't grab it.
> 
> 
>     Spencer Yost
> 
> 
> 
>     Spencer Yost
> 
>         > > On Oct 12, 2017, at 3:24 PM, Brian VanDragt wrote:
> > 
> >         You are lucky they were only $10. I needed to replace them in my JD 70 throttle lever which is a metal plate with friction disks bonded to both sides. I checked the price at my dealer, it was $92, so I wasn't going to do that. I ordered a reproduction for around $30. The reproductions have white rubber disks which I didn't think was going to work, but I installed it anyway, and I was right. It held ok but just felt bad. I took it back out and the rubber was balling up and peeling off of the face of the disks. I took my original plate and cut out disks from brake pad material and glued them on myself. Now it feels smooth and holds like it should. If anybody wants my reproduction rubber one (JD #AA6077R) I will give it to you.
> > 
> >         Brian
> > 
> >             > > > On October 11, 2017 at 11:17 PM Spencer Yost wrote:
> > > 
> > > 
> > >             I fixed the throttle tonight. Turns out the friction disks are just cork. I wish someone had taken a picture of my face when I picked them up at the John Deere dealer. Was feeling real stupid that I paid nearly 10 bucks for 2 cork discs I could've made in my shop in five minutes.
> > > 
> > >             In my defense, the old ones were so compressed and glazed I believe them to be some sort of composite material. I include the pictures of the old ones below. As you can see from the second one that when I go ahead and break the old one I could see the fresh cork.
> > > 
> > >             Live and learn
> > > 
> > >             These two discs go between three pieces of metal. The middle piece of metal has a notch for a roll pin so it won't turn/spin. Looking back that was my clue that they were too compressed. Tightening the throttle as far as I could would not bring that notch up to the roll pin. With fresh cork, I could get that notch there with no problem. The throttle acts wonderful now.
> > > 
> > >             Now that I can get idle and keep it with the throttle I will be able to set idle speed, and therefore be able to time the engine properly. Not to mention actually being able to do work.
> > > 
> > > 
> > > 
> > > 
> > > 
> > >             Spencer Yost_______________________________________________
> > >             AT mailing list
> > >             http://www.antique-tractor.com/mailman/listinfo/at
> > > 
> > >         > > _______________________________________________
> >         AT mailing list
> >         http://www.antique-tractor.com/mailman/listinfo/at
> > 
> >     > 
>     _______________________________________________
>     AT mailing list
>     http://www.antique-tractor.com/mailman/listinfo/at
>