[AT] 430V update

Spencer Yost yostsw at atis.net
Sat Nov 25 06:11:45 PST 2017


I got Home late from family celebrations last night. The service manual was waiting on the front porch.  This morning I checked into the things I needed to find out. I have not found them yet.  The manual appears to be a summarization of what's new and different about the 420/430. It makes many references to the original model 40 manual. The governor/throttle linkage section is one of them :-(. The manifold bolts are not in the torque specifications list either.

Still looking in case I missed them...

However I did find one thing and I need to give some points away to Cecil.  As he suggested it might be, the  John Deere 430 is also a tractor that is timed at fast idle.  It runs smooth at fast idle and I have a great electronic tach to confirm fast idle speed so I'll get the timing easy as pie after reassembly.



Spencer Yost



Spencer Yost
> On Nov 23, 2017, at 8:35 AM, Cecil Bearden <crbearden at copper.net> wrote:
> 
> Spencer:
> 
> If you have the time, you can cut a piece of 3/4 plywood to fit, using 
> the old seat cover as a pattern, then paint the plywood with several 
> coats of linseed oil based paint, or use the old fashioned Pine tar 
> water repellent  paint formula.  When you make the vinyl cover, I try to 
> make it in as few pieces as possible.  With this seat back, there would 
> be 3 pieces.  The original probably had 4. I would sew each end into the 
> cover, then make the top, front, bottom, and back in one piece that 
> would wrap around and also the open end that is shown at the top of the 
> picture you sent would be at the bottom.  That way, when it is rained 
> on, the water would shed off and any moisture inside would drain out the 
> bottom.  A good hardware store will have the nut inserts for the wood in 
> the back.  When you assemble it use never-seize liberally on the bolts.  
> Also a dab of silicone sealant around the hole in the vinyl will stop 
> moisture from getting into the back.
> 
> I realize this is a long post, but little details like this are the 
> difference between a seat lasting 10 years in outdoors service, or 2 years.
> 
> Cecil in oKla
> 
> 
>> On 11/22/2017 10:43 PM, Spencer Yost wrote:
>> Thanks Tyler!
>> 
>> 
>> That's a pretty ingenious solution.   The picture did not come through for me either so I am reattaching it. I texted a slightly different way than I normally do, but not sure why that would have anything to do with it.
>> 
>> Anyways here it is again:
>> 
>> 
>> 
>> 
>> 
>> Spencer Yost
>> 
>> 
>> 
>> Spencer Yost
>>> On Nov 22, 2017, at 11:08 PM, Tyler Juranek <tylerpolkaman at gmail.com> wrote:
>>> 
>>> Hi Spencer,
>>> I obviously cannot see the picture, so I don't exactly know your
>>> setup. However, I'll offer this suggestion anyway.
>>> 
>>> In 2015, shortly after I graduated high school, dad built a buddy
>>> seat for my Oliver so I could go on tractor rides and what not.
>>> (Nobody ever liked to ride on the fender telling me which way to go).
>>> Anyway, we went to a salvage yard and bought an Oliver seat frame, and
>>> a seat off a JD 630.
>>> So we cut it in half, put some angle iron in between to make the seat
>>> longer, and then we welded it back together, so it made the seat
>>> longer. We then welded it to the top of the oliver seat frame where
>>> the pan originally was.
>>> Now for the seat cushion...
>>> Dad went to Hobby Lobby and bought a vinal pad cover deal and gave
>>> $6.00 for it! A buddy cut some plywood at the length we needed it.
>>> Another guy had some foam from a furnature store.
>>> We put the foam on the plywood after we cut it, and then cut the
>>> vinal cover to the right length and width. We wrapped it around the
>>> plywood and stapled it together. The cushion sits in the seat frame
>>> like a JD seat.
>>> So if the seat is like that, maybe you could make one out of your own
>>> plywood, foam and cover.
>>> Just a thought.
>>> Take Care,
>>> Tyler Juranek
>>> IA
>>> 
>>>> On 11/22/17, Spencer Yost <yostsw at atis.net> wrote:
>>>> I got a ship confirmation for the 430 technical manual a few days ago.
>>>> Finally. I've had it ordered for weeks. Should be here Friday. But I won't
>>>> have a chance to work on the tractor till this weekend. if the gauge was
>>>> shipped right away I should have it on Friday too.
>>>> 
>>>> With the manual I can get some torque values for the manifold and also do
>>>> the governor throttle linkage adjustment that Dean suggests.  Also, the
>>>> generator barely keeps up the battery. I'm hoping there some wiring
>>>> diagrams/troubleshooting procedures in there so I can doublecheck
>>>> everything. I was re-wiring blindly, but I've done this enough times I feel
>>>> pretty confident that I have a right.  It's a ground issue or a weak
>>>> generator probably.
>>>> 
>>>> I did finally break something on the John Deere.   Pulling into the shop a
>>>> week or so ago, the seat backrest was uncomfortable so I turned around. i'm
>>>> not terribly smart, but I think the plywood is shot :-). The shot is from
>>>> above, looking down.  There used to be a great boat/marine upholstery shop a
>>>> few miles from my house. They did wonderful outdoor rated upholstery work.
>>>> But they are out of business so I don't know who I'm going to use now.
>>>> 
>>>> Regardless, I'm thankful to have something to work on!  Happy Thanksgiving
>>>> everyone!
>>> _______________________________________________
>>> AT mailing list
>>> http://www.antique-tractor.com/mailman/listinfo/at
>>> 
>>> 
>>> _______________________________________________
>>> AT mailing list
>>> http://www.antique-tractor.com/mailman/listinfo/at
> 
> _______________________________________________
> AT mailing list
> http://www.antique-tractor.com/mailman/listinfo/at





More information about the AT mailing list