[AT] Wheel bearings

Cecil Bearden crbearden at copper.net
Mon Jun 5 06:28:59 PDT 2017


My oil supplier supplies fuel oil and grease to the county here. A few 
years ago he was selling about 12 barrels of Mystic JT-7 85-140 Gear oil 
each year to the county for their mowers.  He suggested they try Mystic 
Centra-Lube, commonly called corn picker grease 00 weight.  He went to 
selling 2 barrels of JT-7 and 1 barrel of Centra-lube a year to them.  I 
use Centra-Lube in all my gearboxes, and have even put it in a 
Roadranger transmission with a leaking PTO.  It has to run a few minutes 
when cold, but it shifts like any other 13Spd Roadranger I have driven.

In extreme cold weather (-25 deg F), gear oil would be recommended for 
bearings.  I agree with Steve's link on the use of grease vs oil.   But 
that is in a perfect world.  Tractors are like boats, they aren't right 
unless they leak a little bit.  I will use oil in transmissions and 
engines and rear ends.  Grease everywhere else.

Cecil in OKla


On 6/5/2017 6:48 AM, Stephen Offiler wrote:
> Tyler:
>
> The debate whether to design equipment for grease vs. oil has been going on
> forever.  I found this web site (link below) that does a good job of
> explaining the pro's and con's of each.  This site is oriented toward
> industrial machinery but the majority of it still applies to ALL machinery
> in general, including old tractors.  Another possible factor might relate
> to the chemistry of oils and greases back when your Oliver was designed.
> Additives for oils vs. greases back then would have been a different story
> than they are today.
>
> http://www.machinerylubrication.com/Read/923/grease-oil
>
> SO
>
>
>
> On Mon, Jun 5, 2017 at 12:00 AM, Tyler Juranek <tylerpolkaman at gmail.com>
> wrote:
>
>> Hi Mike,
>>   Yes. They do have that. But we use gun grease in all the other
>> tractors for greasing wheel bearings, so I am wondering, does it
>> matter if the bearings have grease or oil? Or do they serve the same
>> purpose?
>>   Tyler
>>
>> On 6/4/17, Mike M <meulenms at gmx.com> wrote:
>>> Tyler, does your 88 have plugs in the front hubs to accept oil? If so I
>>> believe they were designed for 90 wt gear lube.
>>>
>>> Mike M
>>>
>>> On 6/4/2017 10:14 PM, Dave wrote:
>>>> Hi Tyler,
>>>>       When I Google “Oliver 88 front wheel bearing"
>>>> (http://www.ebay.com/sch/sis.html?_nkw=Oliver+Front+wheel+
>> bearing+kit+70+77+88+Super77+88+770
>>>> <http://www.ebay.com/sch/sis.html?_nkw=Oliver+Front+wheel+
>> bearing+kit+70+77+88+Super77+88+770>)
>>>> they sure as heck look like every other wheel bearing I’ve ever seen
>> since
>>>> I put new ones on my ’48 Ford Convertible a few years ago (~ 1956). I
>>>> really question why the Operators Manual would call for engine oil
>> rather
>>>> than grease.
>>>>       Dave
>>>> PS, Have FUN in the 50 mile ride!
>>>>
>>>>> On Jun 4, 2017, at 9:41 PM, Tyler Juranek <tylerpolkaman at gmail.com>
>>>>> wrote:
>>>>>
>>>>> Hello all,
>>>>> Now that I have the steering fixed in my oliver, I have been running
>>>>> it up and down the road, uphill and downhill, quite often lately, as
>>>>> the 50 mile tractor ride I go on each summer is this next Saturday,
>>>>> June 10.
>>>>> I hired the work done by one of the people that I know from the
>>>>> tractor shows we go to around here. He did an amazing job, it took two
>>>>> new bearings in the steering sector.
>>>>> Anyway, my question deals with wheel bearings.
>>>>> The oliver 88 opperators manual says that the wheel bearings use engine
>>>>> oil.
>>>>> I have a feeling that since most wheel bearings use grease, they
>>>>> probably put grease in them.
>>>>> There seems to be some vibration in the steering wheel, like the front
>>>>> wheels are having trouble moving freely. As I am driving along with
>>>>> someone on the buddy seat, they say the front wheels are moving great.
>>>>> So, does it really matter if there is oil or grease in them?
>>>>> Of course, it could be that some grease needs to be added to the
>>>>> steering box again, but with a 50 mile ride in store for the tractor,
>>>>> I don't want to ruin the $175 a piece wheel bearings over something
>>>>> stupid like not using the right lubricants. Grease and oil mix, so if
>>>>> it is something I need to change, it shouldn't be hard to mix it up.
>>>>> But since the pair of eyes says the wheels look good, it is the old
>>>>> saying, "If it works, don't fix it."
>>>>> Any help is greatly appreciated.
>>>>> Thanks!
>>>>> Tyler Juranek
>>>>> IA
>>>>> _______________________________________________
>>>>> AT mailing list
>>>>> http://www.antique-tractor.com/mailman/listinfo/at
>>>> _______________________________________________
>>>> AT mailing list
>>>> http://www.antique-tractor.com/mailman/listinfo/at
>>>
>>> ---
>>> This email has been checked for viruses by Avast antivirus software.
>>> https://www.avast.com/antivirus
>>>
>>>
>>> _______________________________________________
>>> AT mailing list
>>> http://www.antique-tractor.com/mailman/listinfo/at
>>>
>> _______________________________________________
>> AT mailing list
>> http://www.antique-tractor.com/mailman/listinfo/at
>>
> _______________________________________________
> AT mailing list
> http://www.antique-tractor.com/mailman/listinfo/at





More information about the AT mailing list