[AT] Anyone heard from Bo Hinch?

charlie hill charliehill at embarqmail.com
Tue Jan 24 09:49:12 PST 2017


Cecil I'm really stepping out on a limb here but I want to
say there is a diaphragm somewhere in the system that goes bad
and creates that problem.  My guess is the problem is on the air end
of the compressor not the governor.  I may be wrong.  Like I said, I never
worked on them myself.  Occasionally when they started acting up on
the job the guys would attach a wire to the lever that that rod attaches to
and pull the rod back a bit (towards the air end) to make it run until it 
could
be fixed.  I can't tell you how to do that either particularly on a Detroit.

Hang on a bit and maybe Bo will set us both straight.  I'm pretty sure he 
knows.

Charlie

-----Original Message----- 
From: Cecil Bearden
Sent: Monday, January 23, 2017 6:27 PM
To: Antique tractor email discussion group
Subject: Re: [AT] Anyone heard from Bo Hinch?

OK, that confirms what I was thinking.  It has been 20 years since I set
he rack on a Detroit.  luckily I still have all my old books, just have
to dig them out...   They are buried in some file cabinets behind a
stack of plywood!! That plywood is not on pallets either!!  I think the
problem is the rod from the compressor regulator is a little too long
for cold weather operation...   My problem is that I work with 4cycle
diesels all the time and a Detroit sounds so much different, that  I
have a problem setting the idle speed by ear.   I love Detroits, they
are about the most reliable engine around.

Thanks

Cecil


On 1/23/2017 11:45 AM, charlie hill wrote:
> Cecil,
>
> I'm sure Bo can help you with this better than I can.
> After being around a lot of Detroits I can tell you that
> the idle is controlled by "the rack" and that isn't something
> you need to mess with without experience because if it
> isn't right the engine will run away until it hand grenades.
>
> The problem you are having is most likely related to the pressure relief
> valve.  The Ingersol compressors I'm familiar with don't have detroits but
> I think the set up is about the same.  There is a valve on top of the
> accumulator
> tank that is piped to a solenoid wired to the start button.  There is a 
> rod
> that runs
> from the air end of the compressor to the pump on a JD or Cummins.  I'm 
> not
> sure
> how it's set up for a detroit but that calls on the governor based on air
> demand.
> If it's not right it will shut the engine down or rather lug it down until
> it shuts off.
>
> Of all the screw compressors I've dealt with over the years, if they are
> giving problems
> it is somewhere in that system.  I'm sorry I don't know the correct
> terminology.
> I never work on them because 1)  they weren't my machines and 2) given the
> nature
> of compressed air I didn't want to risk tinkering with it.  I leave that 
> to
> folks that know what
> they are doing. I've never seen a compressor come unglued but I have seen 
> a
> Detroit run away
> and grenade.  It ain't pretty! It will make you want to run!
>
> Charlie
>
> -----Original Message-----
> From: Cecil Bearden
> Sent: Monday, January 23, 2017 10:27 AM
> To: Antique tractor email discussion group
> Subject: Re: [AT] Anyone heard from Bo Hinch?
>
> Bo:
>
> Thanks..  I had a ransom virus in my computer and I had to start over
> lost everything from 2007..  My old Ingersoll 250 rotary ...........   I
> had to start it up in 12 deg weather a few weeks back.  3cyl
> detroit...   It finally fired up with some ether like a typical
> Detroit.   However, when pressure would build up and it would try to
> idle back, it would just die.  I don't have a tach on this machine..   I
> was only needing it at the time to air up a tire.   My electric
> compressor was in another building., and my small compressor used a
> Honda that would not pull start with the cold..   I finally connected a
> 1/2" hose barb orifice to the other valve on the compressor and bled
> enough air to keep the engine throttled up and hold at about 100 lbs
> pressure.  I got the tire aired up and then discovered the oil filter on
> the Detroit started leaking.  New filter and new 15W40 oil, but it was
> cold..     I really don't find a place to set the Idle speed on the
> Detroit.. I know this is a rather dumb question.
>
> Cecil
>
>
> On 1/23/2017 8:32 AM, Bo Hinch wrote:
>> Am still hanging in there Cecil and you can always find me by doing a
>> google search on me . Been meaning to get with you on ALL these books 
>> that
>> I have packed up and ready to go somewhere that you suggested a while 
>> back
>> .The croup has been slowing me down for a while but hope to be back on
>> track shortly . Oh , glad SOMEONE misses me , even if only for 
>> information
>>    .
>>
>> On Mon, Jan 23, 2017 at 8:11 AM, Chuck Saunders <gooberdog at gmail.com>
>> wrote:
>>
>>> Cecil,
>>> The email Bo posted in his latest post to the list was bohinch at gmail.com
>>> Hope this helps
>>> Chuck Saunders
>>>
>>> On Mon, Jan 23, 2017 at 7:57 AM, Cecil Bearden <crbearden at copper.net>
>>> wrote:
>>>
>>>> I haven't seen any posts from Bo in a while, and I lost his email
>>>> address when I got the Ransom Virus I wanted to ask him about a problem
>>>> I have with my old Ingersoll compressor when it is cold...
>>>> Cecil in OKla
>>>> _______________________________________________
>>>> AT mailing list
>>>> http://www.antique-tractor.com/mailman/listinfo/at
>>>>
>>> _______________________________________________
>>> AT mailing list
>>> http://www.antique-tractor.com/mailman/listinfo/at
>>>
>> _______________________________________________
>> AT mailing list
>> http://www.antique-tractor.com/mailman/listinfo/at
> _______________________________________________
> AT mailing list
> http://www.antique-tractor.com/mailman/listinfo/at
>
> _______________________________________________
> AT mailing list
> http://www.antique-tractor.com/mailman/listinfo/at

_______________________________________________
AT mailing list
http://www.antique-tractor.com/mailman/listinfo/at 




More information about the AT mailing list