[AT] More Ford Jubilee Adventures

Tyler Juranek tylerpolkaman at gmail.com
Fri Aug 28 18:04:42 PDT 2015


Hi Warren,
 Did you get all the crap drained out of the tranny?

 Been having a lot of "interesting" findings on my Oliver lately also.
You wouldn't believe all of the water and other stuff that came out of
the rearend when i drained it. So, dad put some gas in the bottom, and
we run it around the yard a time or two to wash the gears up, and then
we flushed it again.
 We put SAE 90 in it, and I drove it about 12 miles, brought it home,
and when I backed it into the shed, something milky was leakin again.
Ug.
 What do you expect? It's not young anymore! Grin!
 Take Care, and please keep us updated!
Tyler Juranek
 IA

On 8/28/15, Mogrits <mogrits at gmail.com> wrote:
> Thanks again for the great advice and more importantly, the moral support.
> You guys are great.
>
> Warren
>
> Oh yeah, I was telling my wife about all the help y'all have been to me
> over the years and how discussion had taken it's annual turn to the
> Portland show and she said she'd consider going with me sometime.
> So...maybe next year. She is the salt of the earth but she is no camper, so
> we will see.
>
> On Fri, Aug 28, 2015 at 10:10 AM, Cecil R Bearden <crbearden at copper.net>
> wrote:
>
>> Since water is heavier than oil, it will sink to the bottom and float
>> the oil out of the transmission.
>>
>> Cecil in oKla
>>
>>
>>
>> On 8/28/2015 7:42 AM, Stephen Offiler wrote:
>> > What you're going thru is completely normal, and your friend's advice
>> > is
>> > spot-on the money.
>> >
>> > In other words, you need to believe that old iron is fun to work on,
>> > and
>> > fun to put to work.  If it's nothing but hassles upon hassles and you
>> have
>> > work that needs to be done reliably, again, listen to your friend.
>> >
>> > SO
>> >
>> >
>> > On Thu, Aug 27, 2015 at 9:20 PM, Mogrits <mogrits at gmail.com> wrote:
>> >
>> >> Gosh this just keeps going. I got the wires on right and went to set
>> >> the
>> >> static timing and removed the inspection cover to look for timing
>> >> marks.
>> >> bumped the motor a few times and chocolate milk came out of the hole
>> >> indicating a leaky transmission seal (engine oil is normal) along with
>> >> a
>> >> leaky transmission. I have to park it outside and assume the shifter
>> boot
>> >> is leaking. So I drained the transmission and got a lot of water out
>> with a
>> >> little oil. Then I googled and found out about the cotter pin that is
>> >> supposed to be in the drain hole in the bellhousing which is missing
>> >> on
>> my
>> >> tractor, and the hole is clogged up. So I cleaned that out and got
>> >> more
>> >> water and oil but the flywheel is still dipping itself in the soup so
>> >> I
>> >> sprayed a lot of carb cleaner through the timing hole while turning
>> >> the
>> >> starter. Hopefully tomorrow it will be flushed I can find out why the
>> >> distributor is stuck and try to get the thing in time.
>> >>
>> >> I asked a friend who is a grading contractor who has operated a lot of
>> Ford
>> >> and New Holland over the years for advice on this tractor and he said
>> "If
>> >> you want to do any work with it, sell it to someone who wants to look
>> at it
>> >> and buy something that works". I know he is right but I have not yet
>> >> reached that point.
>> >>
>> >> Warren
>> >>
>> >> On Fri, Aug 14, 2015 at 12:59 AM, charlie hill <
>> charliehill at embarqmail.com
>> >> wrote:
>> >>
>> >>> Warren,   Pull the spark plugs, spin the engine over slowly, by hand
>> >>> if
>> >>> possible until it comes up top dead center on the #1 piston and on
>> >>> the
>> >>> compression stroke.  Put the #1 spark plug wire on the distributor
>> >>> cap
>> >>> lug that corresponds with where the rotor button is pointing and then
>> >>> connect
>> >>> the rest of the wires in the correct firing order from there.   You
>> >>> may
>> >>> need
>> >>> to
>> >>> pull the distributor out enough to turn the rotor a notch or so on
>> >>> the
>> >> gear
>> >>> but
>> >>> you shouldn't have to move it much.
>> >>>
>> >>> Charlie
>> >>>
>> >>> -----Original Message-----
>> >>> From: Mogrits
>> >>> Sent: Thursday, August 13, 2015 7:53 PM
>> >>> To: Antique tractor email discussion group
>> >>> Subject: Re: [AT] More Ford Jubilee Adventures
>> >>>
>> >>> So it looked to me like the distributor is rotated 180 degrees, as
>> >>> that
>> >> is
>> >>> how the old wires were installed. I put them back correctly and it
>> >>> will
>> >> pop
>> >>> but not come close to running. I'm going to look it up and plan to
>> >>> pull
>> >> the
>> >>> distributor and reinstall and then set the static timing, assuming I
>> can
>> >>> find a standard procedure.
>> >>>
>> >>> Warren
>> >>>
>> >>> On Tue, Aug 11, 2015 at 9:45 PM, Steve Offiler <soffiler at gmail.com>
>> >> wrote:
>> >>>> Just wanted to say there is a ton of good advice here.  Well done
>> >> Howard.
>> >>>> If I could add anything at all, I'd suggest replacing points
>> resistance
>> >>>> test with a voltage drop test.  This has two benefits.  One, most
>> >>>> any
>> >>> volt
>> >>>> meter even real cheap ones will handle it.  Two, it's a real world
>> test
>> >>>> done under the kind of current load the system actually works with.
>> >>>>
>> >>>> Engine off, roll the distributor cam so points are closed.  Connect
>> >> meter
>> >>>> set to volt range across the points. Meaning, one meter lead on the
>> >> coil
>> >>>> terminal that goes to the points, and the other to chassis.  Old
>> analog
>> >>>> meter, watch your polarity.  Digital meter if you're backward it
>> >>>> just
>> >>> puts
>> >>>> up a minus-sign, no big deal.  Now turn on ignition.  Current flows
>> >> thru
>> >>>> coil and points to ground.  If the points are good, voltage will be
>> >>> around
>> >>>> 0.1 volt or less.  If they are bad, they're typically way higher,
>> >>>> like
>> >> a
>> >>>> full volt or more.  This test is not usually ambiguous.  Good vs bad
>> is
>> >>>> very different on even a cheap meter.
>> >>>>
>> >>>> SO
>> >>>>
>> >>>> Sent from my iPhone
>> >>>>
>> >>>>> On Aug 11, 2015, at 7:01 PM, Howard Weeks <weeksh at att.net> wrote:
>> >>>>>
>> >>>>> I don't claim to be any kind of "condenser" expert but here are a
>> >>>>> few
>> >>>>> comments on the subject:
>> >>>>>
>> >>>>> 1. Back in the early 50s, I worked weekends for an old car/tractor
>> >>>>> mechanic. He checked condensers by using a kick test. Basically, he
>> >> put
>> >>>>> the subject condenser in series with a small amp meter and placed
>> >>>>> the
>> >>>>> combination across a 6 or 12 volt battery momentarily. If you got a
>> >>> good
>> >>>>> kick on the amp meter and then nothing, the cap was good. No kick
>> >> meant
>> >>>>> it was bad. Any continuous current meant it was also bad. Be sure
>> >>>>> to
>> >>>>> discharge the cap by shorting it before connecting across the
>> >> battery.
>> >>>>> This test always worked for him.  I have an old piece of test
>> >> equipment
>> >>>>> here that also checks a cap in the same manner. Some people can do
>> >> this
>> >>>>> test with one of the older design ohmmeters. The new digital meters
>> >>> will
>> >>>>> not do the test.
>> >>>>>
>> >>>>> 2. I have been restoring antique radios in some form for most of my
>> >>> life
>> >>>>> and I have a lot of both old and late model test equipment designed
>> >> for
>> >>>>> evaluating capacitors. Most of the ignition caps that I have
>> >>>>> checked
>> >>>>> measured approximately .17 - .2 microfarads in capacity. The choice
>> >> of
>> >>>>> this capacity is a function of the coil design and if properly
>> >> selected
>> >>>>> by the designer, the system should run indefinitely and not pit the
>> >>>>> points. If they pit badly, it is a sign that the coil and cap are
>> >>>>> not
>> >>>>> properly matched or selected. Which side of the points gets pitted
>> >> is a
>> >>>>> sign of whether the cap is high or low in value for a particular
>> >>>>> combination of cap and coil. I am not trying to say that they have
>> >>>>> to
>> >>> be
>> >>>>> a "matched set" - just that a gross change in cap or coil type
>> >>>>> could
>> >> be
>> >>>>> a problem. Most of the old ignition reference books from back in
>> >>>>> the
>> >>> 20s
>> >>>>> and 30s do a pretty good job of explaining how they work and how to
>> >>> test
>> >>>>> them. I can't honestly say that I have ever found a truly bad
>> >>> condenser.
>> >>>>> But I have had hell with the point resistance (don't know where
>> >>>>> they
>> >>>>> were made)!
>> >>>>>
>> >>>>> 3. When point are closed, they should measure less than 1 ohm -
>> >>>>> preferably close to zero ohms ever time they close for the ignition
>> >> to
>> >>>>> work properly. If they measure 2 - 5 ohms, the system will either
>> >>>>> not
>> >>>>> run or it will be very sick. Same for magneto or standard ignition
>> >>>>> system. Many of the cheaper ohm meters will not accurately measure
>> >>>>> resistances below a few ohms.
>> >>>>>
>> >>>>> 4. The resistors that are in series with some coils are designed to
>> >>>>> limit the current through the coils when the engine is running. The
>> >> DC
>> >>>>> current through the coils should be in the range of 3 - 6 amps or
>> >>>>> so
>> >>>>> when the engine is running. RPM and dwell settings will affect the
>> >>>>> amount of current to some extent. If a coil designed for a resistor
>> >> is
>> >>>>> run without one, it will run for awhile but the coil will overheat
>> >> and
>> >>>>> usually quit fairly quickly. Putting a momentary short across that
>> >>>>> resistor when starting the engine would produce a hotter spark for
>> >>>>> starting purposes.
>> >>>>>
>> >>>>> 5. Pay some attention to the polarity of the coil connection to the
>> >>>>> distributor. If you have a negative ground battery system, the "-"
>> >> end
>> >>>>> of the coil should be connected to the distributor. The "+" end of
>> >> the
>> >>>>> coil goes to the distributor if a you have a positive ground
>> >>>>> system.
>> >>>>>
>> >>>>> Don't know if any of this spiel is useful to anyone but it
>> >>>>> accurately
>> >>>>> describes my experience with Kettering ignition systems.
>> >>>>>
>> >>>>> Howard in GA
>> >>>>>
>> >>>>>> On 8/9/2015 2:30 PM, Mogrits wrote:
>> >>>>>> I don't disagree with you on anything you said, except the
>> >>>>>> resistor
>> >>> has
>> >>>>>> been bypassed on my tractor and it uses a coil that needs no
>> >> resistor.
>> >>>>>> Substituting for the new, correct condensor produces a spark. The
>> >> new
>> >>>>>> condensor does not. So there is definitely a need to replace that
>> >>>>>> particular condensor.
>> >>>>>>
>> >>>>>>> On Sun, Aug 9, 2015 at 2:13 PM, Ron Cook <ron at lakeport-1.com>
>> >> wrote:
>> >>>>>>> There is usually no reason to replace a condenser.  Starting
>> >> problems
>> >>>>>>> with Ford N tractors can usually be traced to the resistor.
>> >>>>>>> And I certainly do agree on the crap that is sold these days
>> >>>>>>> being
>> >> no
>> >>>>>>> good right out of the box.  I quit going to TSC years ago for
>> >>>>>>> that
>> >>>>>>> very
>> >>>>>>> reason.  So too, did many.  TSC closed their store in Sioux City.
>> >>>>>>> It has actually helped my generator/starter repair business a
>> >> little.
>> >>>>>>> The do it yourself bunch have lost their cheap parts supplier,
>> >> which
>> >>>>>>> really were not cheap anyway considering you always have to buy
>> >>>>>>> two
>> >>> or
>> >>>>>>> more to fix the problem.
>> >>>>>>> Ron Cook
>> >>>>>>> Salix, IA
>> >>>>>>>
>> >>>>>>>> On 8/9/2015 5:52 AM, Cecil R Bearden wrote:
>> >>>>>>>> I went through the same thing with a fence charger 2 weeks ago.
>> >>>> Worked
>> >>>>>>>> all afternoon in 105 heat index to get wire up around yard to
>> >>>>>>>> keep
>> >>>>>>>> pet
>> >>>>>>>> bull in.  Had a good charger in a tool box next to the other
>> >>>>>>>> elect
>> >>>>>>>> service at the South Barn.  It would barely spark.  Dug out the
>> >>> brand
>> >>>>>>>> new Zareba charger from TSC that had never been used, it had no
>> >>>>>>>> spark.
>> >>>>>>>> Took the Harbor Freight solar one off the back fence and it was
>> >>> shot.
>> >>>>>>>> Took the Parmak solar fencer off the divider fence for the
>> >>>>>>>> horses
>> >>> and
>> >>>> it
>> >>>>>>>> worked!!!
>> >>>>>>>>
>> >>>>>>>> I certainly hope the pertronix system fixes your
>> >>> problem...Condensers
>> >>>>>>>> are being made in China or some other 3rd world country, so
>> >> quality
>> >>>> is a
>> >>>>>>>> problem...
>> >>>>>>>>
>> >>>>>>>> Cecil in OKla
>> >>>>>>> _______________________________________________
>> >>>>>>> AT mailing list
>> >>>>>>> http://www.antique-tractor.com/mailman/listinfo/at
>> >>>>>> _______________________________________________
>> >>>>>> AT mailing list
>> >>>>>> http://www.antique-tractor.com/mailman/listinfo/at
>> >>>>> _______________________________________________
>> >>>>> AT mailing list
>> >>>>> http://www.antique-tractor.com/mailman/listinfo/at
>> >>>> _______________________________________________
>> >>>> AT mailing list
>> >>>> http://www.antique-tractor.com/mailman/listinfo/at
>> >>>>
>> >>> _______________________________________________
>> >>> AT mailing list
>> >>> http://www.antique-tractor.com/mailman/listinfo/at
>> >>>
>> >>> _______________________________________________
>> >>> AT mailing list
>> >>> http://www.antique-tractor.com/mailman/listinfo/at
>> >>>
>> >> _______________________________________________
>> >> AT mailing list
>> >> http://www.antique-tractor.com/mailman/listinfo/at
>> >>
>> > _______________________________________________
>> > AT mailing list
>> > http://www.antique-tractor.com/mailman/listinfo/at
>>
>>
>> ---
>> This email has been checked for viruses by Avast antivirus software.
>> https://www.avast.com/antivirus
>>
>> _______________________________________________
>> AT mailing list
>> http://www.antique-tractor.com/mailman/listinfo/at
>>
> _______________________________________________
> AT mailing list
> http://www.antique-tractor.com/mailman/listinfo/at
>



More information about the AT mailing list