[AT] Tractor tire liquid

Mike meulenms at gmx.com
Mon Oct 20 09:29:41 PDT 2014


Could it be the rubber seal in the valve stem itself that is not 
compatible with methanol?

Mike M

On 10/20/2014 9:27 AM, Cecil R Bearden wrote:
> The tubes are butyl rubber.  Butyl rubber is listed as compatible with
> methanol.  This is also a 25% methanol/water mix.     I bought the
> methanol from my oil supplier who sells this for tractor tire ballast
> anti-freeze all the time.
>
> Cecil in OKla
>
>
> On 10/20/2014 8:15 AM, Stephen Offiler wrote:
>> Respectfully disagree.  This is WAY too broad and general a statement.
>> There *are* certain types of rubber that get along just fine with
>> methanol.  Otherwise you'd never be able to run it thru a flexible hose or
>> seal it with an O-ring.
>>
>> SO
>>
>> On Mon, Oct 20, 2014 at 8:51 AM, Steve W. <swilliams268 at frontier.com> wrote:
>>
>>> Cecil R Bearden wrote:
>>>> I need a little input from you guys.
>>>>
>>>> a couple weeks ago I mounted 2 new 18.4x38 tires on my 2-105 White.
>>>> Tires were mounted tubeless with some type of fluid in the tire.  I
>>>> think it may have been some type of glycol based anti-freeze .  One rim
>>>> needed some welding on a rusted place as the rim had been outside since
>>>> last summer after removing the tire.  We mounted the tires & tubes with
>>>> no problems noted.  Filled both tires with methanol/water solution.  I
>>>> used windshield washer fluid when methanol was so much more expensive.
>>>> Tires hold about 100 gallons, so we added 1/2 of a barrel of methanol.
>>>> filled the remaining with air.  while sowing wheat about 2 weeks later,
>>>> one tire started leaking water at the valve.  I checked the valve and
>>>> found it to be loose from the tube.  2 days later I pumped the fluid out
>>>> and broke down the tire and found valve separated from the tube and a
>>>> 1inch long cut about 6 inches from the valve.  I assumed the cut was
>>>> from a pinch with the tire spoon.  Or, maybe the tube was caught between
>>>> the tire & rim.  We inflated and deflated the tube to straighten it
>>>> out.   We also used tire mounting lube to mount the tire on the rim.  I
>>>> repaired the tube last Wednesday.  Yesterday I noticed fluid running out
>>>> of the valve hole on the other tire and a lot of the mounting lube had
>>>> coagulated at the base of the tire.  I jacked the tire up and put the
>>>> valve on top as I did not have time to work on it.
>>>>
>>>> My question is 2 part.   Would the use of mounting lube cause a loose
>>>> tire on the rim and it possibly slip and pull the valve out??   Would
>>>> the use of Methanol be deteriorating the rubber in the tube. and causing
>>>> the problem.  These tires are Speedway 18.4 x 38 8 ply rating.  Tubes
>>>> were 2 different brands.   Gateway the first one, and Doberman the
>>>> second.  I was only pulling a 16 ft spring tooth with a 12 ft harrow
>>>> behind it on 30 acres and later a 16x8 JD drill before the first tire
>>>> started leaking...  The load was not anything out of the ordinary.
>>>>
>>>> Cecil in OKla
>>> Methanol eats rubber REAL quick. I would bet the methanol is the only
>>> reason for the problem.
>>>
>>>
>>> --
>>> Steve W.
>>> _______________________________________________
>>> AT mailing list
>>> http://www.antique-tractor.com/mailman/listinfo/at
>>>
>> _______________________________________________
>> AT mailing list
>> http://www.antique-tractor.com/mailman/listinfo/at
>
> ---
> This email is free from viruses and malware because avast! Antivirus protection is active.
> http://www.avast.com
>
> _______________________________________________
> AT mailing list
> http://www.antique-tractor.com/mailman/listinfo/at
>




More information about the AT mailing list