[AT] OT: Rosebuds! The oxi-acetylene kind...

[charlie hill]

Cecil, that agrees with what I've seen people do.

Charlie

-----Original Message----- 
From: Cecil R Bearden
Sent: Friday, November 15, 2013 8:16 AM
To: Antique tractor email discussion group
Subject: Re: [AT] OT: Rosebuds! The oxi-acetylene kind...

You can reheat the gears to about 400 deg ( have to check on the alloy)
and then quench in oil.  It will re-temper the gears, but they will not
be as hard as when first manufactured.  The hardness reduces with each
heating.  When burying the gears in hot charcoal, the metal will pick up
carbon from the charcoal and case harden f quenched in water as soon as
removed from the heat.

Cecil in OKla

On 11/15/2013 12:03 AM, Tom wrote:
> Only one problem, Charlie, the gear teeth will be the first to heat.
> So they will lose their temper before the hubs will be hot enough to
> free on the shafts.
>
> Tom
>
>
>
>
>
>> ________________________________
>> From: charlie hill <charliehill at embarqmail.com>
>> To: Antique tractor email discussion group <at at lists.antique-tractor.com>
>> Sent: Friday, 15 November 2013 12:43 PM
>> Subject: Re: [AT] OT: Rosebuds! The oxi-acetylene  kind...
>>
>>
>> Tom I don't think you have to get them that hot in terms of max temp.
>> You just have to get enough heat into the mass of metal to make the metal
>> expand and break the joint loose.  When you have a big mass of metal it
>> takes
>> a lot of BTU's.
>>
>> Charlie
>>
>> -----Original Message-----
>> From: Tom
>> Sent: Thursday, November 14, 2013 6:27 PM
>> To: Antique tractor email discussion group
>> Subject: Re: [AT] OT: Rosebuds! The oxi-acetylene kind...
>>
>> One would have to wonder how hard the gears & shafts were after that
>> experience!
>>
>> Tom
>>
>>
>>
>>
>>
>>> ________________________________
>>> From: Mike <meulenms at gmx.com>
>>> To: Antique tractor email discussion group 
>>> <at at lists.antique-tractor.com>
>>> Sent: Friday, 15 November 2013 12:05 PM
>>> Subject: Re: [AT] OT: Rosebuds! The oxi-acetylene  kind...
>>>
>>>
>>> Interesting that you would bring that up Charlie, I was watching RFD-TV
>>> the other night and they were interviewing a guy that had restored Power
>>> Horse tractors.. Parts are apparently very hard to get for those
>>> tractors, you either need to make them or have a parts tractor. Anyway,
>>> he said when he got it the transmission gears were seized up, so he
>>> filled the transmission with charcoal briquets and let it burn, same
>>> type of idea. Those are neat little tractors by the way, made to be
>>> controlled just like a horse using reins to control the tractor via two
>>> levers.
>>> Mike M
>>>
>>> On 11/14/2013 7:22 AM, charlie hill wrote:
>>>> Dave if the part is such that you can do it without messing something
>>>> else
>>>> up
>>>> you might find you have better success, and cheaper, by just building a
>>>> big
>>>> fire and throwing the part in the bed of coals for a while.
>>>>
>>>> Charlie
>>>>
>>>> -----Original Message-----
>>>> From: Dave Johnson
>>>> Sent: Thursday, November 14, 2013 12:31 AM
>>>> To: at at lists.antique-tractor.com
>>>> Subject: [AT] OT: Rosebuds! The oxi-acetylene kind....
>>>>
>>>> I'm pretty ok with cutting & brazing, but have never used a rosebud to
>>>> heat
>>>> something, and my experience today has me scratching my head.
>>>> The project at hand is freeing up a cast iron wheel hub, stuck on a 
>>>> keyed
>>>> 1"
>>>> shaft. This is on an old Gilson / MW garden tractor transmission.... 
>>>> the
>>>> idea is to liberate a set of 4 of these hubs to make dual adapters for
>>>> use
>>>> on another tractor with a FEL.
>>>>
>>>> I have soaked it for quite some time and have a puller tensioned on it,
>>>> but
>>>> it's not moving.... so now it's time for a little heat.
>>>>
>>>> I bought a new victor 8-MFA rosebud and lit it off as I would the 
>>>> torch,
>>>> but
>>>> when I try to get a blue flame, it flames out with a pop!
>>>>
>>>> What's going on here? Do I not want a hot blue flame, or do I simply 
>>>> need
>>>> to
>>>> feed a lot more of both gases to the torch? Or??  Any insight into 
>>>> these
>>>> things would be appreciated!
>>>>
>>>>       btw, I'm on digest, so it'll take a day for me to respond (:<((
>>>>
>>>>
>>>> Dave in Gilroy, CA
>>>> webguydave at yahoo.com
>>>> _______________________________________________
>>>
>> _______________________________________________
>> AT mailing list
>> http://www.antique-tractor.com/mailman/listinfo/at
>>
>>
>> _______________________________________________
>> AT mailing list
>> http://www.antique-tractor.com/mailman/listinfo/at
>>
>>
>>
> _______________________________________________
> AT mailing list
> http://www.antique-tractor.com/mailman/listinfo/at

_______________________________________________
AT mailing list
http://www.antique-tractor.com/mailman/listinfo/at