[AT] OT--Kawasaki starter trouble
Will Powell
william.neff.powell at comcast.net
Wed Aug 7 04:27:20 PDT 2013
Wow, you have so many things going on...
I agree with Charlie, check your battery.
I have many motorcycles that have similar small starters. I usually jump them with a car battery when I want to prove that I don't have a low amperage issue. Of course I never crank the starter very long because I know prolonged turning will burn it up.
Here's a posting from one Kawasaki forum:
http://www.kawasakimotorcycle.org/forum/kawasaki-atv-mule/96230-mule-2510-starter-issue.html
There's no isolated incidence. If your starter is failing there are probably other Kawasaki owners with the same problems.
Here's another quote from that forum:
Default
My 1999 Mule 2510 will also turn slowly when first hitting the starter; I thought I had it figured out when I replaced the battery and it seemed good for a while. Then it was back to either slow turning or not able to turn at all. A starter rebuild and cable cleaning did not make any difference.
An overnight battery charge and viola!--rapid starting. What I've read in this forum about poor alternator performance seems to be my problem. If I start and stop a lot, without a lot of running time, it will significantly draw down the battery. I've considered adding an auxiliary alternator to my Mule, but would likely do my own setup considering the Kawasaki alternator setup costs almost $1000.
This is the entire thread, they seem to have resolved a lot of your issues:
http://www.kawasakimotorcycle.org/forum/kawasaki-atv-mule/55011-mule-2510-starting-problems.html
Good luck.
Will
<blockquote>
</blockquote>
----- Original Message -----
From: "charlie hill" <charliehill at embarqmail.com>
To: "Antique tractor email discussion group" <at at lists.antique-tractor.com>
Sent: Wednesday, August 7, 2013 6:41:05 AM
Subject: Re: [AT] OT--Kawasaki starter trouble
John, two things come to mind for you to ponder. Does your battery have
enough amperage and is it in good shape?
Does the engine have a compression release when it is starting and is it
functioning properly?
On the compression release, years ago I had a riding mower with similar
starting/starter problems. I finally scraped the thing.
Some time later I read that the engine in it had an automatic compression
release that would fail to operate if he engine oil
wasn't changed regularly enough. The mower was already gone so I was never
able to find out if there was any truth to it.
Don't know that it has a thing to do with your Mule. Just throwing it out
there for you to consider.
Charlie
-----Original Message-----
From: jtchall at nc.rr.com
Sent: Tuesday, August 06, 2013 10:18 PM
To: Antique tractor email discussion group
Subject: [AT] OT--Kawasaki starter trouble
Pardon the OT post but I’m running out of ideas. I’m having trouble with the
starter on my 2000 model Kawasaki Mule. To be honest, I’ve had starter
trouble for several years. I’ll start from the beginning. When it was about
5 years old, the starter went out. Don’t remember what, could have been
clicking, grinding, sluggish. I ordered an aftermarket from DB Electrical to
replace the high dollar Denso that came on it. Starter problems seemed
solved for a couple more years. Eventually troubled returned so I ordered
another one from DB. Problems went away again. About 2-3 years ago they came
back. Couldn’t figure out why the starter wouldn’t engage. Turned the gear
around on the flywheel, no help. Cleaned things up, swapped starters a few
times and it sort of went to working. Last year, more starter trouble. I
remembered that a lot of Deere riding mowers with Kawasaki engines have
starter trouble, so much so that the dealers stock a “fix” for the problem.
It’s just a a relay (I think) you add in the harness, cost about $30 and
takes 15 minutes to install. I picked one up and put it on, problems went
away for a while. For the past 3-4 months the starter sometimes grinds
instead of engaging. I sent one of the Chinese starters as well as the
original Denso to a rebuild shop to be checked. They supposedly rebuilt
them. I put the original back on and to begin with it worked fine, then it
would vary in RPM’s or just click. Put on the supposedly rebuilt Chinese
starter and it grinds instead of engaging like the other aftermarket one. I
added a ground wire between the battery and the starter frame and cleaned
the original ground, still no luck. Checked the voltage at the battery and
where it connects to the starter (solenoid bolts onto the starter), it shows
around 14, drops to 12.5 or so while cranking. When checking across the
solenoid while cranking it shows around 12.5, until it fails to engage, then
it shows 10.8. I ran a jumper wire from the hot battery wire to the blade
terminal on the solenoid to bypass the switch, still doesn’t work correctly.
The only other thing I haven’t eliminated is the neutral start switch, could
it possibly fail slightly and prevent me from getting full voltage to the
starter? Something up with the solenoid—all 3 of them?
Anyone got any ideas on this besides buying another starter/solenoid
assembly? I find it hard (but not impossible) to believe all 3 are
bad—remember 2 were supposedly inspected and repaired.
John Hall
_______________________________________________
AT mailing list
http://www.antique-tractor.com/mailman/listinfo/at
_______________________________________________
AT mailing list
http://www.antique-tractor.com/mailman/listinfo/at
More information about the AT
mailing list