[AT] Bearing interchange help

[Bill Brueck]

All I'm finding is the 41480 which crosses to Timken 2788.  A guy on eBay
has that for $11.23 and his shipping charges are reasonable. Spot checking
the other numbers confirms that the going rate is about $30 each.

I did find that Timken has the 2011 catalog online which I downloaded.  As
one would expect, in this case I got the same results on this quest with
both the old and the new catalog.  But key to this document being useful is
the fact that it's searchable.  I use this to back reference Timken numbers
to other manufacturers, especially Deere, even though the catalog isn't
organized that way.

www.timken.com/pl-pl/products/Documents/Timken_Bearing_Cross_Reference_Guide
.pdf


Bill Brueck
   Pine Island, MN USA

-----Original Message-----
From: at-bounces at lists.antique-tractor.com
[mailto:at-bounces at lists.antique-tractor.com] On Behalf Of Cecil R Bearden
Sent: Wednesday, November 07, 2012 10:58 PM
To: Antique tractor email discussion group
Subject: Re: [AT] Bearing interchange help

I think I have that one..    You can interchange about everything but 
bearings and seals.  For them you have to subscribe to a service or buy a cd
or book..

NHnumbers are:
86512026
86512027
41480
86977427
86512014

Cecil in OKla


On 11/7/2012 10:16 PM, Bill Brueck wrote:
> Hi, Cecil.
>
> I have a pretty complete Timken book in searchable .pdf format.  Send 
> me the NH numbers and I'll see if it plays.
>
> If anybody wants a copy, I got it off the Timken website a couple of 
> years ago for free.  If you can't find it we'll figure out a way to get my
copy to
> you.  It's almost 400 pages, 2003 version, 3.5 meg file.   Hmmm, a couple
of
> years, huh.  But plenty new for the stuff I work on.
>
> Bill Brueck
>     Pine Island, MN USA
>
> -----Original Message-----
> From: at-bounces at lists.antique-tractor.com
> [mailto:at-bounces at lists.antique-tractor.com] On Behalf Of Cecil R 
> Bearden
> Sent: Wednesday, November 07, 2012 8:59 PM
> To: Antique tractor email discussion group
> Subject: Re: [AT] Bearing interchange help
>
> My 617 New Holland disc mower has bit the dust again.   This time I am
> putting in all new bearings and a new pinion gear in the gearbox.  I 
> have to nearly tear it complete apart to put the lower shaft in the 
> gearbox, so it is going to get a complete overhaul. The PO had trouble 
> with it during warranty and I think that the dealer tried to save a few
> bucks and should have replaced the pinion.   They also have an update
> for the complete pinion shaft and gears.  The NH dealer may be able to 
> shed some light on this. Anyhow, I don't want to pay  $30 each for a 
> simple tapered roller bearing, so I am trying to find a replacement.  
> I have the NH part number, but cannot interchange it.
> Any help would be appreciated.    I would rather not call the bearing
> house and get a dumb look over the phone.  If I have the bearing 
> number, I get a lot better price.
>
> Cecil in OKla
>
>
> _______________________________________________
> AT mailing list
> http://www.antique-tractor.com/mailman/listinfo/at
>
>> _______________________________________________
>> AT mailing list
>> http://www.antique-tractor.com/mailman/listinfo/at
> _______________________________________________
> AT mailing list
> http://www.antique-tractor.com/mailman/listinfo/at
>
>
>
> _______________________________________________
> AT mailing list
> http://www.antique-tractor.com/mailman/listinfo/at

_______________________________________________
AT mailing list
http://www.antique-tractor.com/mailman/listinfo/at