[AT] Off Topic, Meyers versus Western Snow Plows on 1985 F250?

William Powell william.neff.powell at comcast.net
Tue Nov 30 02:10:26 PST 2010


Ever had  buyers remorse? 

Looked at the plow yesterday. The holding part was on the truck. Also
noticed that the holder was welded pretty heavily to the frame of the truck
on the back part. Plow looked good, Painted, not perfect but no holes or
visible welds. 

He had a Meyers power unit on it. He said the Meyers unit does not go with
the plow and that he had the western pump. Asked to see the western unit, he
pulled it out of the barn. Says it works. Said he had the switches also. No
manual.  I did not see the switches but I should have asked to see them. I
also don't know if it has a wiring harness. 

I should have walked away and said I will get back to him... But, I was
thinking I don't have the time to look around. Told him I wanted it but I
did not want to have to fabricate the unit to get it on my truck. I wanted
it to bolt on.  What if I get there and its cut off and there are no rear
brackets? That would mean fabrication on my end. If he cuts it off how am I
going to be sure it will fit on my truck? I can fabricate brackets but I
really don't want to. 

Also, I have not seen it work, he says it does but what recourse will I have
if it does not? If it does have a wiring harness can he ground it and put
voltage to it and make it work? Is that unreasonable to ask? 

Then I gave him the contact information with the guy that had the Myers plow
since I had agreed to buy the Western. 

Am I being picky for $500? Maybe I'm predicting the worst. It may just be OK
after all... But driving away I just did not have a good feeling, I just
thought, he comes another project.

Anybody have a manual to an old Western plow? Any pictures of the blade
holding unit that I can pattern from? 

Regards,

Will




-----Original Message-----
From: at-bounces at lists.antique-tractor.com
[mailto:at-bounces at lists.antique-tractor.com] On Behalf Of Louis
Sent: Monday, November 29, 2010 10:17 PM
To: 'Antique tractor email discussion group'
Subject: Re: [AT] Off Topic, Meyers versus Western Snow Plows on 1985 F250?

I have plowed with both, Western and Meyers. I have had the same basic
Western unit for 15 years now,  all I have had to do is replace 2 motors.
Meyers, I always carried spare coils and solenoids. I had a new Meyers plow
back in the 80's, the coils started to go bad within 2 years. I think the
Western is a better plow.  For a full size pick up, you need at least a 7"6"
blade.  I think with a 7' blade, when you angle it, it won't be wide enough,
without the tires running over unplowed snow.  $500 is a fair price.  Check
all the pivot points, and wear edge of the blade.  Look for non factory
welds. 

Lou 

-----Original Message-----
From: at-bounces at lists.antique-tractor.com
[mailto:at-bounces at lists.antique-tractor.com] On Behalf Of Will Powell
Sent: Monday, November 29, 2010 11:29 AM
To: Antique tractor email discussion group
Subject: [AT] Off Topic, Meyers versus Western Snow Plows on 1985 F250?


Hello, 

I'm looking for a plow for my old 1985 F250 Ford Diesel Truck. 

I've found 2 somewhat near me. A Western about 20 miles away, owner says its
off a 1984 F250 and that he has several other F250's with Meyers and he
wants them all the same. 7' 6" blade. I know the 1984 F250 is essentially
the same as a 1985. 

The other is a 7ft Meyers about 40 miles away off of a 1986 F250. 

Both owners are asking $500. 

I'm leaning for the closer Western plow. Is there a big difference between
both of the plows? Is $500 a fair offer? 

Regards, 

Will
_______________________________________________
AT mailing list http://www.antique-tractor.com/mailman/listinfo/at




_______________________________________________
AT mailing list
http://www.antique-tractor.com/mailman/listinfo/at




More information about the AT mailing list