[AJD] Part Number F301R

[Bill Brueck]

Ah, I had thought it was an outer bearing race.  From Greg's description,
I'm wondering if one could turn a replacement out on a lathe?  Or is the
metal too thin for that?

B²

Bill Brueck
   Chatfield, Minnesota, USA

Confusion is a higher state of knowledge than ignorance.
 

-----Original Message-----
From: antique-johndeere-bounces at lists.antique-tractor.com
[mailto:antique-johndeere-bounces at lists.antique-tractor.com] On Behalf Of
greg at theoldtractorcompany.com
Sent: Thursday, July 17, 2008 8:35 PM
To: Antique John Deere mailing list
Subject: Re: [AJD] Part Number F301R

F301R is N/A from all traditional outlets.
Basically it's a cup to hold the PTO shaft seals.

You can bet however that there is at least one lurking out there somewhere

Greg




NOW!! CHECK YOUR PART #'S AT WWW.JOETRAKTOR.COM!

WE ARE NO LONGER ON THE JOHN DEERE PARTS LOCATOR


Greg Stephen
The Old Tractor Company
Stephen Equipment Company
PO Box 709
Franktown, CO 80116
303-663-5246
1-866-381-8703 FAX 
> I am not reading this the same way you are but I am not a parts expert 
> by
> 
> any  means
> 
> I see F 298 R as a seal for the bearing.......
> 
> Frank
> 
> ----- Original Message -----
> 
> From: "Dean Van Peursem" deanvp at att.net
> >
> To: "'Antique John Deere mailing list'"
> 
> antique-johndeere at lists.antique-tractor.com>
> Sent: Thursday, July 17, 2008 11:29 AM
> 
> Subject: Re: [AJD] Part Number F301R
> 
> 
> 
> 
> 
> > Charles,
> 
> >
> 
> > You might want to check if this is sold by JD as an
> assembly along with
> > other
> 
> > parts. Check out F298R which is the bearing assembly. 
> Also check if you
> > can
> 
> > find any numbers on the cup or bearing, if so you may
> be able to cross
> > reference
> 
> > to the original manufacturer.
> 
> >
> 
> >
> 
> > Dean Van Peursem
> 
> > Snohomish, WA
> 
> >
> 
> > If we take the time to count our blessings we don't
> have time to complain.
> >
> 
> >
> 
> >
> 
> > -----Original Message-----
> 
> > From: antique-johndeere-bounces at lists.antique-tractor.com
> > [antique-johndeere-bounces at lists.antique-tractor.com] On Behalf Of
> > 
> charleslendman at bellsouth.net
> > Sent: Thursday, July 17, 2008 9:19 AM
> 
> > To: antique-johndeere at lists.antique-tractor.com
> > Subject: [AJD] Part Number F301R
> 
> >
> 
> > I have a 1951 Styled John Deere model G I need this
> part number F301R..its
> > shown
> 
> > on page 130 of the parts manual reference number 63
> they call it a
> > cup...Does
> 
> > anyone know where i could get one? Listed as obsolete
> and not available
> > from
> 
> > Deere..! Thanks for aly help or any leads! Charles
> 
> > _______________________________________________
> 
> > Antique-johndeere mailing list
> 
> > http://www.antique-tractor.com/mailman/listinfo/antique-johndee
> re
> >
> 
> > _______________________________________________
> 
> > Antique-johndeere mailing list
> 
> > http://www.antique-tractor.com/mailman/listinfo/antique-johndee
> re
> >
> 
> 
> 
> _______________________________________________
> 
> Antique-johndeere mailing list
> 
> http://www.antique-tractor.com/mailman/listinfo/antique-johndee
> re
> 
> 
> 



_______________________________________________
Antique-johndeere mailing list
http://www.antique-tractor.com/mailman/listinfo/antique-johndeere