[AJD] Plow Measur

[Bruce Mahr]

On a one bottom, you measure just like I said previously, from the point of 
the share out toward the furrow wheel,  just to the edge of the unplowed 
furrow wall, it is at a right angle to the point and landside outward.

Bruce Mahr

----- Original Message ----- 
From: "Frank" <gremaux at midrivers.com>
To: "Antique John Deere mailing list" 
<antique-johndeere at lists.antique-tractor.com>
Sent: Monday, September 11, 2006 8:10 PM
Subject: Re: [AJD] Plow Measur


> yup...clear except my plow has only one bottom
>
> Frank
> gremaux at midrivers.com
> Central Montana
> http://www.angelfire.com/mt/deeregp/index.html
> ----- Original Message ----- 
> From: "Duane Ledford" <dledford at classicnet.net>
> To: "Antique John Deere mailing list" 
> <antique-johndeere at lists.antique-tractor.com>
> Sent: Monday, September 11, 2006 6:47 PM
> Subject: Re: [AJD] Plow Measur
>
>
>> Say you have a two bottom plow. Mark a line from the rearward bottom's 
>> point straight forward  past the forward bottom, making essentially a 
>> parallel line between the two bottoms. The distance from the point of the 
>> forward plow point to the line coming from the rearward plow point is 
>> your measurment. 12, 14, 16,etc. On a lot of plows, you can measure the 
>> distance between beams, but not all, as some have offset shanks. Clear as 
>> mud now?
>> ----- Original Message ----- 
>> From: "Frank" <gremaux at midrivers.com>
>> To: "Antique John Deere mailing list" 
>> <antique-johndeere at lists.antique-tractor.com>
>> Sent: Monday, September 11, 2006 6:28 PM
>> Subject: Re: [AJD] Plow Measur
>>
>>
>>> still do not understand
>>>
>>> Frank
>>> gremaux at midrivers.com
>>> Central Montana
>>> http://www.angelfire.com/mt/deeregp/index.html
>>> ----- Original Message ----- 
>>> From: "Bruce Mahr" <martian at winco.net>
>>> To: "Antique John Deere mailing list" 
>>> <antique-johndeere at lists.antique-tractor.com>
>>> Sent: Monday, September 11, 2006 12:09 PM
>>> Subject: Re: [AJD] Plow Measur
>>>
>>>
>>>> >From the tip of the share straight out at a 90 degree angle from the 
>>>> >tip,
>>>> not the length of the share or moldboard.
>>>>
>>>> Bruce Mahr
>>>>
>>>> ----- Original Message ----- 
>>>> From: "Gordon Hart" <grnacres at pgtc.net>
>>>> To: "Antique John Deere mailing list" 
>>>> <antique-johndeere at lists.antique-tractor.com>
>>>> Sent: Monday, September 11, 2006 12:36 PM
>>>> Subject: [AJD] Plow Measur
>>>>
>>>>
>>>> How are moldboard plows measured?
>>>> Gordon
>>>> _______________________________________________
>>>> Antique-johndeere mailing list
>>>> http://www.antique-tractor.com/mailman/listinfo/antique-johndeere
>>>>
>>>>
>>>> _______________________________________________
>>>> Antique-johndeere mailing list
>>>> http://www.antique-tractor.com/mailman/listinfo/antique-johndeere
>>>>
>>>
>>>
>>> _______________________________________________
>>> Antique-johndeere mailing list
>>> http://www.antique-tractor.com/mailman/listinfo/antique-johndeere
>>
>> _______________________________________________
>> Antique-johndeere mailing list
>> http://www.antique-tractor.com/mailman/listinfo/antique-johndeere
>>
>
>
> _______________________________________________
> Antique-johndeere mailing list
> http://www.antique-tractor.com/mailman/listinfo/antique-johndeere
>