[Farmall] Seed Plate Drive

[Richard Pope]

Yep, I'll just use the one off the old final drive.

Richard


----- Original Message ----- 
From: "Bobby Guilbeau" <bguilbea at bellsouth.net>
To: "'Farmall/IHC mailing list'" <farmall at lists.antique-tractor.com>
Sent: Thursday, May 04, 2006 7:17 PM
Subject: RE: [Farmall] Seed Plate Drive


> Now that we are all on the same page looks like Jim was correct about what
> you were trying to take off.
>
> Of course the million dollar question now is do you have a cover?
>
> Bobby
>
>
>
> -----Original Message-----
> From: farmall-bounces at lists.antique-tractor.com
> [mailto:farmall-bounces at lists.antique-tractor.com] On Behalf Of Richard 
> Pope
> Sent: Thursday, May 04, 2006 8:16 PM
> To: Farmall/IHC mailing list
> Subject: Re: [Farmall] Seed Plate Drive
>
> Jim, Al and Bobby:
>
> Thank you all for your info.  Here is a photo of the part that I'm trying 
> to
>
> remove:
>
> http://img61.imageshack.us/my.php?image=p50352297we.jpg
>
> This next photo is the final drive that I took off the tractor:
>
> http://img61.imageshack.us/my.php?image=p50352353rr.jpg
>
> Perhaps it has a thick washer under that bolt that I can use on the new
> final drive and then I'll just use the cap also.
>
> Thanks,
>
> Richard
>
>
> ----- Original Message ----- 
> From: "Jim Becker" <jim.becker at verizon.net>
> To: "Farmall/IHC mailing list" <farmall at lists.antique-tractor.com>
> Sent: Thursday, May 04, 2006 4:49 PM
> Subject: Re: [Farmall] Seed Plate Drive
>
>
>> Al,
>> I think Richard has gotten past the step of removing the sprocket and is
>> trying to get the plate drive shaft off.  It is held with a cap screw
>> about the same way the Cub sprocket is held on.
>>
>> Richard,
>> Removing the cap screw won't cause any other problems.  What I don't
>> remember off the to top of my head is what you need to reinstall if you
>> are going to use the tractor without the drive.  Seems like you need to
>> reinstall the cap screw with a washer of some sort, and install a cover 
>> in
>
>> place of the drive.  The cap screw is about 3/8 x 3/4.
>>
>> Jim Becker        jim.becker at verizon.net
>>
>> ----- Original Message ----- 
>> From: "Al Jones" <aljones at ncfreedom.net>
>> To: "'Farmall/IHC mailing list'" <farmall at lists.antique-tractor.com>
>> Sent: Thursday, May 04, 2006 5:42 PM
>> Subject: RE: [Farmall] Seed Plate Drive
>>
>>
>>> No.  The cap screw is a bolt that goes through two sets of holes--one in
>>> the sprocket, one in the hollow shaft that comes out the final drive
>>> case.  I think it is "supposed" to be a pin with a cotter pin in the end
>>> of it.  But it may be a 5/16" bolt with a nut on the end, as that's
>>> what's in mine.  You may have to tap/twist the sprocket to make it come
>>> off but I can't imagine you tearing anything up unless you decide to cut
>>> it off with a torch :)
>>>
>>> PS I think the Cub sprocket was held on with a single cap screw.
>>>
>>> Al
>>>
>>> -----Original Message-----
>>> From: farmall-bounces at lists.antique-tractor.com
>>> [mailto:farmall-bounces at lists.antique-tractor.com] On Behalf Of Richard
>>> Pope
>>> Sent: Thursday, May 04, 2006 5:58 PM
>>> To: Farmall/IHC mailing list
>>> Subject: Re: [Farmall] Seed Plate Drive
>>>
>>> Hi Jim:
>>>
>>> By removing this cap screw, will I have any chance of messing anything
>>> up
>>> inside the final drive?  What size is this cap screw?  Thanks for your
>>> help,
>>> it is appreciated!
>>>
>>> Richard Pope
>>> Apple Valley, CA
>>>
>>>
>>> ----- Original Message ----- 
>>> From: "Jim Becker" <jim.becker at verizon.net>
>>> To: "Farmall/IHC mailing list" <farmall at lists.antique-tractor.com>
>>> Sent: Thursday, May 04, 2006 6:07 AM
>>> Subject: Re: [Farmall] Seed Plate Drive
>>>
>>>
>>>> Been a long time since I took one off.  As I recall, look in the end
>>> of it
>>>> and you will find the head of a cap screw.  Take it out and the piece
>>> will
>>>> slide off.
>>>>
>>>> Jim Becker        jim.becker at verizon.net
>>>>
>>>> ----- Original Message ----- 
>>>> From: "Richard Pope" <popeman at verizon.net>
>>>> To: "Farmall/IHC mailing list" <farmall at lists.antique-tractor.com>
>>>> Sent: Thursday, May 04, 2006 6:37 AM
>>>> Subject: [Farmall] Seed Plate Drive
>>>>
>>>>
>>>> List:
>>>>
>>>> I need info on how to remove the "Seed plate drive" from the final
>>> drive
>>>> on my Super A.  Is it threaded and just unscrews, or do I have to
>>> perform
>>>> major surgery?
>>>>
>>>> http://img74.imageshack.us/my.php?image=p50352297er.jpg
>>>>
>>>> Thanks in advance,
>>>>
>>>> Richard Pope
>>>> Apple Valley, CA
>>
>> _______________________________________________
>> Farmall mailing list
>> http://www.antique-tractor.com/mailman/listinfo/farmall
>>
>
>
> _______________________________________________
> Farmall mailing list
> http://www.antique-tractor.com/mailman/listinfo/farmall
>
>
> _______________________________________________
> Farmall mailing list
> http://www.antique-tractor.com/mailman/listinfo/farmall
>