[AT] IH B275 Diesel
Kevin
ironman1962 at earthlink.net
Wed Dec 6 17:22:32 PST 2006
Well if they say .09 Volt they aint like what I said. 460-560 IH Diesel, All
I was saying was how mine work.
If ya put a .09v light bulb on 12 v its going to glow very bright for a
fraction of a second,
then won't glow at all any more. Wow wonder who was the brilliant mechanic
that figgerd thatn out ! If its .09v you need to get the manual. Cause
there has to be a resistor to get that low voltage.
What year is this tractor anyways ?
Dont seem like .09 volts would heat much in the summer.
Kevin Mosier
----- Original Message -----
From: "Dave Merchant" <nesys_com at ameritech.net>
To: "Antique tractor email discussion group" <at at lists.antique-tractor.com>;
"Antique tractor email discussion group" <at at lists.antique-tractor.com>
Sent: Wednesday, December 06, 2006 2:56 PM
Subject: Re: [AT] IH B275 Diesel
> It really sounds like these ones are wired in series (which is dumb, but
> you work with what you got),
> so each one wants only a fraction of a volt. As the plug says, 0.9 volt.
>
> If you put 12 V on one, it should glow very bright for a fraction of a
> second,
> then won't glow at all any more.
>
> Dave Merchant
>
>
> At 08:40 AM 12/6/2006, Kevin wrote:
>>If these are like 460-560D they each need 12 volts, take one out and clip
>>a jumper on pos terminal.
>>Touch the gloplug to the tractor, is good to have a cigar ready to light
>>at this time for if the gloplug is good it will get red hot in seconds. If
>>not set it aside and try another. Once you find out which ones are good,
>>get replacements for the bad. Then rewire the whole thing !
>>A poor man has poor ways
>>ironman
>>Kevin Mosier
>>----- Original Message ----- From: "Gus" <gibsongus at earthlink.net>
>>To: "Antique tractor email discussion group"
>><at at lists.antique-tractor.com>
>>Sent: Tuesday, December 05, 2006 11:21 PM
>>Subject: Re: [AT] IH B275 Diesel
>>
>>
>>>John I have a B275 and I had to change some of the glplugs there are two
>>>circuts in each plug hot to first plug ground to hot next plug and so one
>>>last plg is grounded...
>>>
>>>-----Original Message-----
>>>>From: John Kennedy <ihctractor at hotmail.com>
>>>>Sent: Dec 5, 2006 11:06 AM
>>>>To: at at lists.antique-tractor.com
>>>>Subject: Re: [AT] IH B275 Diesel
>>>>
>>>>I think that your plugs are grounded to the engine though the threads It
>>>>doesn't make any sence that the would be in series as they would only
>>>>work
>>>>if you had 6 of them. The wires going in and out of the plug are there
>>>>so
>>>>that you can use one wire from the switch to light up all of the plugs.
>>>>
>>>>The last plug should only have one wire to it, it should not be
>>>>grounded.
>>>>That will only ground out your hot wire to the plugs.
>>>>
>>>>A freind of mine who was Electrician always said I don't understand how
>>>>automotives wiring works with on one wire. I told that the frame was the
>>>>other wire, he still had a hard time understanding that.
>>
>>>AT mailing list
>>>Remembering Our Friend Cecil Monson 11-4-2005
>>>http://www.antique-tractor.com/mailman/listinfo/at
>>
>>_______________________________________________
>>AT mailing list
>>Remembering Our Friend Cecil Monson 11-4-2005
>>http://www.antique-tractor.com/mailman/listinfo/at
>
> Dave Merchant
> kosh at nesys.com
> nesys_com at ameritech.net
>
> http://www.nesys.com
> http://www.nesys.org
>
>
> _______________________________________________
> AT mailing list
> Remembering Our Friend Cecil Monson 11-4-2005
> http://www.antique-tractor.com/mailman/listinfo/at
More information about the AT
mailing list