[Farmall] Farmall Super M Axle Leak

Tue Apr 11 07:57:25 PDT 2006

Richard,

  Please share your results. I need to do the same for my "H".

  Thanks.

  Ed Greany
  Pinon Hills

Richard Pope <popeman at verizon.net> wrote:
 Mike & Bruce:

Thanks so much for the info. I'll pull it apart today and see if I can get 
a seal number so I can try NAPA. If not, I'll order from Case IH, as I'm 
about 90 miles away from the closest one.

Richard Pope
Apple Valley, CA

----- Original Message ----- 
From: "Mike Sloane" 
To: "Farmall/IHC mailing list" 
Sent: Tuesday, April 11, 2006 5:53 AM
Subject: Re: [Farmall] Farmall Super M Axle Leak

>I had the same problem with my super M. There is a seal on the axle that 
>can be relatively easily changed. You need to remove the wheel hub, clean 
>any rust and junk off the axle shaft, and pull the outer cap. Behind that 
>is the paper gasket 48950D, a felt washer 45085D, and the actual seal that 
>sits in the axle housing 360457R91. You have to dig the old seal out with 
>an ice pick or something and then carefully tap the new one in. Take note 
>of which face is out on the old one. If you damage the paper gasket, just 
>make a new one out of an old file folder or "Pendaflex" folder - the 
>material isn't critical. Nor is the felt washer (which is there to keep 
>grease out of the seal area, not keep transmission fluid in the axle, and 
>the grease is mainly to keep dirt out of the axle housing). The key item is 
>the axle seal. If you can read the manufacturer's part number on the old 
>seal, you can probably get a replacement through NAPA or a local bearing 
>dealer cheaper than at Case IH. (I don't have any Case IH dealer within 100 
>miles, and the shipping charges on the seal are more than the cost of the 
>item, so I am forced to seek substitutes for that kind of thing.)
>
> When you remove the old seal, some lubricant will run out, unless you have 
> the tractor tipped up some. Or else just catch it in a bucket and pour it 
> back in after you are done. Naturally, you will want to check the bearing, 
> clean up the cap
>
> Mike
>
> Richard Pope wrote:
>> List:
>>
>> I just bought new rear tires for my Super M. I'm wire brushing the
>> rims and wheels preparing for paint. Both rear axles are leaking
>> oil. Is there a seal or gasket that I can replace to prevent these
>> leaks? Would greasing those grease fittings help any? I doubt that
>> it's been greased in many years.
>>
>> Thanks,
>>
>> Richard Pope Apple Valley, CA
>
>
> -- 
> Mike Sloane
> Allamuchy NJ
> 
> Website: 
> Images: 
>
> If Tyranny and Oppression come to this land, it will be in the guise of
> fighting a foreign enemy. -James Madison, fourth US president (1751-1836)
>
>
> -- 
> No virus found in this outgoing message.
> Checked by AVG Free Edition.
> Version: 7.1.385 / Virus Database: 268.4.0/306 - Release Date: 4/9/2006
>
>
> _______________________________________________
> Farmall mailing list
> http://www.antique-tractor.com/mailman/listinfo/farmall
> 

_______________________________________________
Farmall mailing list
http://www.antique-tractor.com/mailman/listinfo/farmall

--0-1987208572-1144767445=:19805
Content-Type: text/html; charset=iso-8859-1
Content-Transfer-Encoding: 8bit

<div>Richard,</div> <div> </div> <div>Please share your results. I need to do the same for my "H".</div> <div> </div> <div>Thanks.</div> <div> </div> <div>Ed Greany</div> <div>Pinon Hills Richard Pope <popeman at verizon.net> wrote:</div> <BLOCKQUOTE class=replbq style="PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #1010ff 2px solid">Mike & Bruce: Thanks so much for the info. I'll pull it apart today and see if I can get a seal number so I can try NAPA. If not, I'll order from Case IH, as I'm about 90 miles away from the closest one. Richard Pope Apple Valley, CA ----- Original Message ----- From: "Mike Sloane" <MIKESLOANE at VERIZON.NET> To: "Farmall/IHC mailing list" <FARMALL at LISTS.ANTIQUE-TRACTOR.COM> Sent: Tuesday, April 11, 2006 5:53 AM Subject: Re: [Farmall] Farmall Super M Axle Leak >I had the same problem with my super M. There is a seal on the axle
 that >can be relatively easily changed. You need to remove the wheel hub, clean >any rust and junk off the axle shaft, and pull the outer cap. Behind that >is the paper gasket 48950D, a felt washer 45085D, and the actual seal that >sits in the axle housing 360457R91. You have to dig the old seal out with >an ice pick or something and then carefully tap the new one in. Take note >of which face is out on the old one. If you damage the paper gasket, just >make a new one out of an old file folder or "Pendaflex" folder - the >material isn't critical. Nor is the felt washer (which is there to keep >grease out of the seal area, not keep transmission fluid in the axle, and >the grease is mainly to keep dirt out of the axle housing). The key item is >the axle seal. If you can read the manufacturer's part number on the old >seal, you can probably get a replacement through NAPA or a local bearing
 >dealer cheaper than at Case IH. (I don't have any Case IH dealer within 100 >miles, and the shipping charges on the seal are more than the cost of the >item, so I am forced to seek substitutes for that kind of thing.) > > When you remove the old seal, some lubricant will run out, unless you have > the tractor tipped up some. Or else just catch it in a bucket and pour it > back in after you are done. Naturally, you will want to check the bearing, > clean up the cap > > Mike > > Richard Pope wrote: >> List: >> >> I just bought new rear tires for my Super M. I'm wire brushing the >> rims and wheels preparing for paint. Both rear axles are leaking >> oil. Is there a seal or gasket that I can replace to prevent these >> leaks? Would greasing those grease fittings help any? I doubt that >> it's been greased in many
 years. >> >> Thanks, >> >> Richard Pope Apple Valley, CA > > > -- > Mike Sloane > Allamuchy NJ > <MIKESLOANE at VERIZON.NET> > Website: <WWW.GEOCITIES.COM mikesloane> > Images: <WWW.FOTKI.COM mikesloane> > > If Tyranny and Oppression come to this land, it will be in the guise of > fighting a foreign enemy. -James Madison, fourth US president (1751-1836) > > > -- > No virus found in this outgoing message. > Checked by AVG Free Edition. > Version: 7.1.385 / Virus Database: 268.4.0/306 - Release Date: 4/9/2006 > > > _______________________________________________ > Farmall mailing list > http://www.antique-tractor.com/mailman/listinfo/farmall > _______________________________________________ Farmall mailing
 list http://www.antique-tractor.com/mailman/listinfo/farmall </BLOCKQUOTE>