[Steam-engine] 1971 ASME Code

[Dan Donaldson]

    Do you have experience riveting boilers and installing threaded stays 
Jeff?  Where is your shop located and how much do you charge per hour shop 
time?

Dan Donaldson


----- Original Message ----- 
From: "JEFF LUND" <lundmachineworks at yahoo.com>
To: "Steam-engine mailing list" <steam-engine at lists.stationary-engine.com>
Sent: Tuesday, March 29, 2005 4:25 PM
Subject: Re: [Steam-engine] 1971 ASME Code


> Dan,  you may want to check you local library network.
> I have found some older code book through
> inter-library loan in the southern minnesota area.
> For $350 a code book is a good price.    That is close
> to what the current editions cost.
>
> Jeff Lund
> Lund Machine Works
> R-stamp
>
> --- Dan Donaldson <ddonaldson at tampatank.com> wrote:
>>     I failed to mention that a certified shop with
>> an "S" stamp will be
>> doing the rivet and stay bolt installation.  I will
>> be doing the detail
>> drawings for the boiler and I am interested in a
>> copy of the ASME code for
>> reference.
>>
>> Dan Donaldson
>>
>>
>>
>> ----- Original Message ----- 
>> From: "Dan Donaldson" <ddonaldson at tampatank.com>
>> To: "Steam-engine mailing list"
>> <steam-engine at lists.stationary-engine.com>
>> Sent: Tuesday, March 29, 2005 1:15 PM
>> Subject: Re: [Steam-engine] 1971 ASME Code
>>
>>
>> >    I am looking at building a new riveted boiler
>> for an engine I have and
>> > I need the ASME code pertaining to riveted
>> construction for power boilers.
>> >
>> > Dan Donaldson
>> >
>> >
>> > ----- Original Message ----- 
>> > From: "JEFF LUND" <lundmachineworks at yahoo.com>
>> > To: "Steam-engine mailing list"
>> <steam-engine at lists.stationary-engine.com>
>> > Sent: Tuesday, March 29, 2005 12:38 PM
>> > Subject: Re: [Steam-engine] 1971 ASME Code
>> >
>> >
>> >> Do you need the whole code book, or could you
>> just get
>> >> the sections you need?   The National board will
>> copy
>> >> by the page, but it is still quite costly.  Are
>> you
>> >> riveting?   If you are there is a separate
>> section
>> >> that is sometimes reference for riveting.
>> >>
>> >> Jeff Lund
>> >> Lund Machine Works
>> >> New Ulm, MN
>> >>
>> >> --- Dan Donaldson <ddonaldson at tampatank.com>
>> wrote:
>> >>>     Does anyone know where I can get a copy of
>> the
>> >>> ASME code Section I,
>> >>> Power Boilers, 1971 Edition?  The National Board
>> has
>> >>> it available but they
>> >>> want $335.00 for it.
>> >>>
>> >>> Dan Donaldson
>> >>>
>> >>> _______________________________________________
>> >>> Steam-engine mailing list
>> >>>
>> >>
>>
> http://www.stationary-engine.com/mailman/listinfo/steam-engine
>> >>>
>> >>
>> >>
>> __________________________________________________
>> >> Do You Yahoo!?
>> >> Tired of spam?  Yahoo! Mail has the best spam
>> protection around
>> >> http://mail.yahoo.com
>> >> _______________________________________________
>> >> Steam-engine mailing list
>> >>
>>
> http://www.stationary-engine.com/mailman/listinfo/steam-engine
>> >>
>> >
>> > _______________________________________________
>> > Steam-engine mailing list
>> >
>>
> http://www.stationary-engine.com/mailman/listinfo/steam-engine
>> >
>>
>> _______________________________________________
>> Steam-engine mailing list
>>
> http://www.stationary-engine.com/mailman/listinfo/steam-engine
>>
>
>
>
> __________________________________
> Do you Yahoo!?
> Yahoo! Small Business - Try our new resources site!
> http://smallbusiness.yahoo.com/resources/
> _______________________________________________
> Steam-engine mailing list
> http://www.stationary-engine.com/mailman/listinfo/steam-engine
>