[AJD] dltx carburator part

[Frank]

Marc
look on the carb body.........dltx and then a number..........sounds like 34 
maybe?

Frank
gremaux at tein.net
Central Montana
http://www.angelfire.com/mt/deeregp/index.html
----- Original Message ----- 
From: "Marc Raasch" <mraasch at hickorytech.net>
To: "Antique John Deere mailing list" 
<antique-johndeere at lists.antique-tractor.com>
Sent: Sunday, July 24, 2005 12:41 PM
Subject: Re: [AJD] dltx carburator part


> The bowl is a dlt 13
> JD #r10009
> The reason I didn't want to use epoxy is that I plan on
> selling this carb either on Le Suer swap meet of on EBay.
> If i were using on a tractor of mine I guess I would doctor it up
> with epoxy
> Marc
> ----- Original Message ----- 
> From: "Frank" <gremaux at tein.net>
> To: "Antique John Deere mailing list" 
> <antique-johndeere at lists.antique-tractor.com>
> Sent: Sunday, July 24, 2005 9:30 AM
> Subject: Re: [AJD] dltx carburator part
>
>
>> it might also be a 26 or 46 which would also be quite different
>>
>> Frank
>> gremaux at tein.net
>> Central Montana
>> http://www.angelfire.com/mt/deeregp/index.html
>> ----- Original Message ----- 
>> From: <greg at theoldtractorcompany.com>
>> To: "Antique John Deere mailing list" 
>> <antique-johndeere at lists.antique-tractor.com>
>> Sent: Saturday, July 23, 2005 10:55 PM
>> Subject: Re: [AJD] dltx carburator part
>>
>>
>>>
>>> Marc
>>> We usually just rework the seating area where the seat seals against and 
>>> if needed apply a bit
>>> of expoxy. Never had a problem after that
>>> I am sure there are more techically correct repairs but it's always 
>>> worked for us. I usually
>>> only replace a bowl if it has been cracked, I don't care for cracks.
>>> Also, you had best check your DLT # so you are sure to get the right 
>>> bowl as there are three
>>> (right?) different bowls. One for the brass body carbs, one for the 
>>> common carbs and one for
>>> the DLTX71 "big nut" carb.
>>> Greg
>>>
>>> Greg Stephen
>>> The Old Tractor Company
>>> Stephen Equipment Company
>>> PO Box 709
>>> Franktown, CO 80116
>>> 303-663-5246
>>> 303-468-0377 FAX<<--GREAT WAY TO REACH ME!
>>>
>>> On Sat Jul 23 16:22 , 'Marc Raasch' <mraasch at hickorytech.net> sent:
>>>
>>>>Looking for any body that might have a fload bowl
>>>>for two cylinder jd tractor.
>>>>Can't get the needle seat to seal down properly as it is
>>>>to much on one side where the gasket seals.  Thanks for any help
>>>>Marcus Raasch
>>>>St Peter MN.
>>>>mraasch at hickorytech.net
>>>>_______________________________________________
>>>>Antique-johndeere mailing list
>>>>http://www.antique-tractor.com/mailman/listinfo/antique-johndeere
>>>
>>>
>>>
>>> _______________________________________________
>>> Antique-johndeere mailing list
>>> http://www.antique-tractor.com/mailman/listinfo/antique-johndeere
>>>
>>>
>>
>> _______________________________________________
>> Antique-johndeere mailing list
>> http://www.antique-tractor.com/mailman/listinfo/antique-johndeere
>>
>>
>>
>> -- 
>> No virus found in this incoming message.
>> Checked by AVG Anti-Virus.
>> Version: 7.0.338 / Virus Database: 267.9.4/57 - Release Date: 7/22/2005
>>
>>
>
> _______________________________________________
> Antique-johndeere mailing list
> http://www.antique-tractor.com/mailman/listinfo/antique-johndeere
>
>