[AJD] JD 40 Carb

greg at theoldtractorcompany.com greg at theoldtractorcompany.com
Tue Sep 7 09:54:33 PDT 2004


Leroy
Wait a sec. Can you tell me what the part # was of the kits you just bought? That might settle some questions. Also the price range so I know what brand of kit they are.
Greg

Greg Stephen
The Old Tractor Company
Stephen Equipment Company
Box 709
7460 E Hiway 86
Franktown, CO 80116
303-663-5246
303-688-4170 fax


------------------------------------------------
On Tue, 7 Sep 2004 7:40:40 -0400, LeRoy Price <lep at epix.net> wrote:

> Duane,
> 
> Both kits had the needle with the tip you mention but there was a slight difference in the seat length when I compared the old with the new.  The old ones screw in very nice, no fighting.  I also noticed that the float looked a bit shorter from the original but not much.
> 
> Maybe I should order another from Greg rather then Wenger's here in PA.
> 
> LeRoy
> 
> 
> > 
> > From: "Duane Larson" <jdlarson at comcast.net>
> > Date: 2004/09/07 Tue AM 12:30:12 EDT
> > To: "Antique John Deere mailing list" <antique-johndeere at lists.antique-tractor.com>
> > Subject: Re: [AJD] JD 40 Carb
> > 
> > LeRoy,
> > That sounds strange - I've built a bunch of TSX carburetors and rarely have
> > a problem screwing the seat in place.  I wonder if you were given a wrong
> > kit, or it contains the wrong needle and seat.  Does the needle have a viton
> > (rubber) tip?  I don't recall a problem with needle size, but it is late and
> > I can look at my notes later today.
> > 
> > Another distinct possibility is the float is hanging on the cast body - that
> > is hard to see, make sure the float arms are symmetric as if they are bent
> > much they will drag and not cause the needle to seat.  Bruce was right - you
> > should be able to hear the float move up and down as you turn the carb.
> > Duane Larson
> > 
> > ----- Original Message ----- 
> > From: "LeRoy Price" <lep at epix.net>
> > To: "Antique John Deere mailing list"
> > <antique-johndeere at lists.antique-tractor.com>
> > Sent: Monday, September 06, 2004 10:28 PM
> > Subject: Re: [AJD] JD 40 Carb
> > 
> > 
> > >
> > > Yup, I had problems putting that seat in and I believe you are talking
> > about that little O ring that seat under it.  You know I bought 2 carb sets
> > for each JD 40 I have.  The seats seems to be slightly taller.  I had to go
> > out and buy a screw driver that was wider but still was a tad short at the
> > blade.  I got it in both carbs almost 3 quarters in before I really had to
> > apply pressure.  I had to give up on the JD 40S it just wouldn't go in but I
> > was able to get it in the 40W.  I did eventually hook up the gas without the
> > body to see if it shut off.  Thats when I saw it leak around the seat, a
> > little more pressure to tighten it seem to work.  But once I get it together
> > it floods.  Not sure how far I can bend the floats down before I don't have
> > enough gas in the bowl.  The kits said JD40 but maybe there marked wrong.  I
> > lostthe original needle or I would have put that one back.  One thing I
> > noticed is that the new needle doesn't fit in the old seat its bigger.  Is
> > that right?
> > >
> > > LeRoy
> > >
> > > Incompetence: When you earnestly believe you can compensate for lack of
> > skill by doubling your efforts, there's no end to what you can't do.
> > >
> > > _______________________________________________
> > > Antique-johndeere mailing list
> > > http://www.antique-tractor.com/mailman/listinfo/antique-johndeere
> > 
> > _______________________________________________
> > Antique-johndeere mailing list
> > http://www.antique-tractor.com/mailman/listinfo/antique-johndeere
> > 
> 
> Incompetence: When you earnestly believe you can compensate for lack of skill by doubling your efforts, there's no end to what you can't do.
> 
> _______________________________________________
> Antique-johndeere mailing list
> http://www.antique-tractor.com/mailman/listinfo/antique-johndeere
> 



More information about the AT mailing list